搜索资源列表
fpgaandmcuand25h20.rar
- FPGA 和ＭＣＵ的并口通信 及ＭＣＵ和Ｅ２ＰＲＯＭ(FM25H20)SPI通信 功能：ＦＰＧＡ对ＭＣＵ的写（ＦＰＧＡ发给ＭＣＵ的地址是写进Ｅ２ＰＲＯＭ的地址 ，Ｅ２ＰＲＯＭ中的数据是 ＦＰＧＡ发送的数据。） ＦＰＧＡ对ＭＣＵ的读（ＦＰＧＡ读取它发给ＭＣＵ在Ｅ２ＰＲＯＭ中存取的数据） 程序和图见附件 恳请高手指导 小弟急啊！,FPGA and MCU
SPI-Driver-For-WinCE-S3C2410.r
- 本驱动程序是基于WinCE系统的s3c2410的SPI驱动源码,The driver is based on the WinCE system s3c2410 the SPI driver source
spi_V1.0.3
- //说 明：msp430通过模拟的spi驱动flash W25X32 //描 述：用于主函数中直接调用 flash写函数 写入数据 //功 能：写入flash 一个字节数据 flash地址自动加一 //端 口：p7.0 接/CS片选端 , p7.1用于时序脉冲, p7.2 用作MOSI主机输出从机输入 ， // p7.3用作MISO主机输入从机输出, // p1.4接/WP写保护引脚 ，此程序里没有用到 所以直接拉高，不用。 // 也可以连写 都试过了
SAM7X256E
- AT91SAM7X256应用资料,包括TEI\SPI\RTC等例程-AT91SAM7X256 application information, including TEI \ SPI \ RTC and other routine
SST25VF016B-SPI
- STM32 读写FALSH- STM32 R/W FALSH
spiflash
- C51的SPI程序例子，经典的spi-flash-spi-flash
spi
- SPI总线接口的verilog源码，包含仿真模块modelsim 和 quartus 工程。本人测试通过。-SPI bus interface in verilog source code, including the simulation module modelsim and quartus project. I test.
SCA100
- 51单片机SPI读取SCA100角度值,带温度补偿,精度达到0.008度.-51 Single-chip SPI read SCA100 angle values, with temperature compensation, accuracy of 0.008 degrees.
FREQSYN
- 使用Verilog语言编写的使用SPI总线设置频率LM2346,可通过设置其R寄存器对其输出频率进行设置（需相应的射频电路相配合）。-The use of Verilog language use SPI bus frequency settings LM2346, can be by setting up its R register set of its output frequency (to be matched by corresponding RF circuitry).
spi_burst
- Verilog block SPI for Burst R/W Operation
sdopration
- SPI模式下，，，，，，，，SD卡的读写-W/R SD card
MAX6902
- SPI RTC MAX6902实时时钟的驱动和应用笔记，及其驱动代码，网上很少关于SPI 的，大家参考一下，一定要8个字节一起写。-SPI RTC MAX6902 RTC driver and application notes, and the driver code, on-line small on the SPI, we refer to, we must write 8 bytes together.
spi_slave
- spi slave 8bit address 1bit r/w 7bit number data
71477212SAM7X256-SPI
- IAR 3.01a IDE编译环境下的SPI读写MAX96XX存储芯片程序-SPI r/w MAX96XX flash ,development in IAR4.03 ide
auto_w_r_spi
- 能够自动读写SPI ROM的控制器，读写的资料直接放到fifo中，经过实际的班子验证，很好用。-Can automatically read and write SPI ROM controller, read and write data directly into fifo, after the actual verification team, very good use.
SDHC
- MSP430F169与SDHC卡的通信程序，支持IO和SPI方式-communication program between SDHC card and MSP430F169.And it is in support of IO as well as SPI mode
SPIFlash
- DOS下通过南桥SPI Controller读写BIOS flash信息的example code，汇编代码-DOS, read and write BIOS flash information through the South Bridge SPI Controller, example in assembly code
spi25
- 铁电SPI 读写 FPG 外挂SPI铁电存储器的读写控制代码.-FM25** SPI R/W
K60PucosiiP28J60ParpPicmp
- K60上移植ucosii，使用spi读写28J60，调试arp，icmp协议-K60 transplant ucosii, using spi r/w 28J60, debugging arp, icmp protocol
spi-slave-mode
- bjx 301a spi 从模式读写数据，-bjx 301a spi slave mode for r/w data