搜索资源列表
breathled
- 基于STM32的呼吸灯，keil uvision4-breathing light based on the STM32 , keil uvision4
light
- 基于STM32 的呼吸灯，使用定时器产生PWM驱动LED，LED接在PA6-Based on the STM32 breathing lights, use a timer to generate PWM drive LED, LED connected to PA6
STM32-pwm
- STM32_PWM利用PWM1来配置输出，可以驱动一个LED灯，实现呼吸灯效果。-STM32_PWM use PWM1 to configure the output can drive an LED light to achieve breathing light effect.
main
- STM32通过延时产生PWM波控制LED灯，形成呼吸灯。-STM32 through delay produce PWM wave to control LED lights, breathing lamp.
STM32-breath_LED
- 用STM32单片机做的一个呼吸灯，可以直接使用，源代码齐全-With STM32 microcontroller do a breathing light, can be used directly, complete source code
hxd
- stm32 呼吸灯 自己可以DIY的 效果还可以 需要的可以-stm32 huxideng
STM32
- 野火开发板 STM32 呼吸灯效果程序，适合新手学习使用-Wildfire STM32 development board breathing light program
STM32-PWM-TIM-GPIO
- 在stm32f103vct6上实现的定时器、adc、gpio以及pwm呼吸灯实验-Implementation of the timer, ADC, GPIO, PWM and breathing lamp experiment on the STM32F103VCT6
TIM_breath
- stm32呼吸灯重映射 stm32呼吸灯重映射-STM32 respiratory lamp re mapping
呼吸灯源程序
- ARM系列呼吸灯源程序，用于各种试验及产品的指示、美观效果渲染。(ARM series breathing light source program)
TIM—呼吸灯
- 呼吸灯，通过stm32控制使得呼吸灯达到所需要的要求(The breathing lamp, which is controlled by STM32, makes the breathing lamp meet the requirements)
实验9 PWM输出实验
- 呼吸灯，利用PWM波实现呼吸灯亮灭。简单历程(Breathing lamp, the use of PWM wave to achieve the extinction of respiratory lights. Simple process)
光敏传感器控制呼吸灯的明暗程度
- 光敏传感器的使用，使用STM32单片机，控制灯的亮的程度。(The use of photosensitive sensors, the use of STM32 microcontroller, control the brightness of the light.)
串口+呼吸灯
- stm32 串口输入字符控制PWM输出 STM32 serial input character control PWM output(STM32 serial input character control PWM output)
TIM—呼吸灯与SPWM波
- STM32例程TIM—呼吸灯与SPWM波(TIM breathing lamp and SPWM wave)
breathe bulb
- 呼吸灯小程序改编，stm32入门小程序联系。(breathe bulb Breathing light applet, stm32 starter applet.)
6. PWM波呼吸灯（测试通过） (1)
- 单片机呼吸灯例程测试通过，使用软件keil。(Single chip microcomputer breathing lamp routine test,Using software Keil.)
STM32F401RE-BLN
- 基于Keil平台实现的呼吸灯，三种频率可用板载按键调节，板子的选择是stm32f401。(A led which lights up or extinguishes like breathing, programmed on Keil using C. You can adjust the frequency by pressing the button on the board. The selection of the board is stm32f401re.)
stm32呼吸灯
- 在STM32F103平台上开发，利用PWM实现呼吸灯效果。(Use of PWM to realize the effect of breathing lamp)
LIGHT
- STM32神舟1号开发板实现通过2个按钮中断来控制流水灯和呼吸灯效果切换(STM32 Shenzhou 1 development board to achieve 2 buttons to interrupt the control of water lamp and breathing lamp effect switching)