搜索资源列表
DTK-IO
- 数字I/O实验主要完成的功能: 在此实验中,SEED-DEC5416 首选进行初始化,包括对外设 UART、本身频率的设定及一些状态区的初始化。然后等待 SEED-MMI5402 发送命令;SEED-DEC5416 响应交通灯自动模式、交通灯手动手动模式、交通灯东西通、交通灯南北通、及交通灯的禁行与夜间模式的操作命令。同时还响应,对 SEED-DEC5416 的复位及两个单元之间的通讯故障。
89c51-IO
- 目前普遍采用的MCS51 和PIC 系列单片机通常只有一个(或没有)UART 异步串行通信接口,在应用系统中若需要多个串行接口(例如在多机通信系 统中,主机既要和从机通信又要和终端通信)的情况下,通常的方法是扩展 一片8251 或 8250 通用同步/异步接收发送芯片(USART),需额外占用单 片机I/O 资源。本文介绍一种用单片机普通I/O 口实现串行通信的方法,可 在单片机的最小应用系统中实现与两个以上串行接口设备的多机通信
Uart
- 软件利用单片机内部的定时器及IO端口实现异步串口,可以在单片机中实现多个串口功能
io-uart
- C51的IO模拟UART,非常好用,对于缺少串口的51单片机很好!
SOFT-UART
- 51 单片机io口模拟串口程序,带中文说明。-soft UART
LSD-TEST430F5438-01_V1.1StudyBoardInstructor
- 利尔达MSP430F5438学习板的中文资料,包含硬件链接,以及IO、UCS、FLASH、WDT、TimeA、TimeB、DMA、硬件乘法器、RTC、RAM、ADC12、UART、SPI、I2C、CRC等各种操作的试验代码。-利尔达board MSP430F5438 learning Chinese data, including hardware, links, and IO, UCS, FLASH, WDT, TimeA, TimeB, DMA, hardware multiplier, R
QT9261_test
- AT91SAM9261开发板附带的IO、LCD、UART等ADS的测试代码,供参考-AT91SAM9261 Development Board attached to IO, LCD, UART, such as ADS test code, for reference
uart
- 51单片机普通I/O口,做串口用,可以和真的串口一样,设置发送和接收的波特率,和发送接收的模式-51 Singlechip general I/O port, serial port used to do, you can and really like the serial port, set up to send and receive baud rate, and send to receive mode
software_uart
- Software uart using a general purpose io and an external interrupt pin of an atmel uc. half duplex operation, adjustable baud rate
first_cpu
- nios ii cpu核,包含通用IO口、sdram、flash、uart-nios ii cpu、genernal io port、sdram、falsh、uart
UART
- 利用UART下的Register (IO最底層),達到透過UART傳送資料,並非使用API或是內建函數,單純使用IO Port。-UART use under the Register (IO bottom) to send data through the UART is not using the API or built-in function, simple to use IO Port.
uart(300bits)
- (小邢)IO模拟串口(300bits),非常稳定可靠.调试通过.-IO serial analog (300bits), very stable and reliable. Debug through.
LCD12864_UART_driver
- 利用 MSC-51 系列单片机 89S51 通过串口方式 驱动 LCD12864 液晶显示器 ,节约了 IO端口 -used MSC-51 series 89S51 to drive LCD12864 by uart
UART
- This UART project is a simple program for the NXP LPC29xx microcontroller using the Hitex LPC2929/39 evaluation board and demonstrating the basic UART and IO functionality.
MCU_FPGA_Interface
- msp430单片机用IO口模拟总线时序,与FPGA进行交互的程序,附源代码,verilog,有简单文档。-msp430 I single-chip analog IO bus with timing, with the FPGA interactive process, with the source code, verilog, a simple document.
pc-uart-mcu51-pwm-moto
- PC机键盘控制MCU产生PWM波,进而控制电动机的转速 利用52单片机外部晶振11.0592MHz,产生准确的波特率119200,实现MCU与PC机的通信,PC机发送字符在 1 - 9 范围内时,MCU的IO口即响应输出对应占空比的pwm波(占空比10 -90 ,10 步进),Pwm波由定时器T0模拟产生。 胡雪川 huxuec@yahoo.com.cn 2010.1.2 程序有待改进完善,不足之处,欢迎各位提出-PC-keyboard control MCU gen
Uart
- 采用串口API 编写的重叠IO方式的串口通信程序,多次测试,性能不错。-com communication program by use com api overlapped io,and have a good performance
mcs51-io-uart
- 利用51的两个输入输出引脚如P1.0和P1.1,置1或0分别代表高低电 平,也就是串口通信中所说的位,如起始位用低电平,则将其置0,停止位为高电平,则将其置 1,各种数据位和校验位则根据情况置1或置0。-Using 51 as the two input and output pins P1.0 and P1.1, set to 1 or 0 representing the high and low, that is said in the bit serial communicati
UART
- STC51单片机使用IO口模拟串行口波特率可变-STC机IO口模拟串行口
a-software-uart
- C8051工作在48Mhz下,完全有能力进行资源的扩展,以实现低成本处理器完成更复杂的任务,文章提出了一种通过单片机普通IO端口完成串口通讯的方法,很好的弥补了通讯端口不足的瓶颈 -C8051 work in 48Mhz, the resource is fully capable of expansion, in order to achieve low-cost processor to complete more complex tasks, the article presents a