搜索资源列表
Eliminator
- 一款用j2me做的手机游戏，测试平台事xp，j2me wirless toolkit-J2ME do with one phone games to test things xp platform, J2ME edge toolkit
adf70201
- ADF7020-1的收发程序si432的收发程序-ADF7020-1 WIRLESS SEND AND RECEIVE
memo
- comparaison between MAC for wirless network sensor
24L01
- c8051f330 编写的2.4G无线模块的驱动程序-c code wirless ,c8051f330 mcu
wirless
- 利用VC_开发无线数据采集软件.pdf 利用串口和modem进行开发的介绍。-VC_ the development of the use of wireless data acquisition software. Pdf using serial port and modem development of the introduction.
adapbeamformin
- contains pdf documents for MIMO in wirless communications, MI_NLMS adaptive beamforming algorithm for OFDM system, narrowband beamforming algorithm for smart antenna
sd
- 一个通过接收无线信号进行工作的源码,通过四位的4000米无线模块传输，传输可加密-A wireless signal through the wirless.
multirateWLANs.pdf
- wlan tenique for scheduler wirle-wlan tenique for scheduler wirless
Antenna_Selection_and_Design
- 设计2.4GHz的短距离无线传输天线的资料-The data for designing 2.4GHz SRD wirless antenna
kftool_matlab
- kalman filter matlab tool help full for understanding the coding for the kalmanfilter, which can either be used for any purposes which could be help for digital signal processing, wirless mobile communication , OFDM .
AVR_Wirless
- Wirless ATMEGA Application with c source code and schematics
MHEED
- MHEED protocol for wirless network sensor
wsn
- some articles about Wirless sensor web
C6000-mcbsp-sample
- C6000 dsp 无线通信 mcbsp 代码-C6000 dsp wirless communication mcbsp code
1000Circuits
- 1000 circuit design in wirless and other
NSWireless
- a program ablout wirless network
wirless
- 1 操作说明： 根据提示输入三位编码（编码不大于255），可以按N键删除编码，按Y键确认，再按UP键为上行，按DOWN键为下行，按S键，为停止。再次按N键为删除编码，可重新输入其它编码进行其它灯的控制。 注：仿真中显示画面是倒着的。 2 用途： 此遥控器用来作智能升降机遥控升降用，当然也可以改成其它用途，整机用锂电池供电，采用专用的无线收发模块，显示用12864点阵液晶显示。有效控制距离，50m左右，欢迎大家欣赏！ 3 打开仿真文件，直
nRF2401
- 无线传输，结合凌阳单片机 *P_Watchdog_Clear = 0x0001 if((nRF2401_RxStatus()) == 1) // nRF2401A有数据请求 { nRF2401_ReceiveByte(RxBuf) // 接收数据 switch(RxBuf[0]) { case 1: PlaySnd(0) // 播放语音"Key1" break
0123745519
- complete wirless design book hope to read
Tcl-script-to-create-dynamic-wirless-nodes-with-A
- Tcl scr ipt to create dynamic wirless nodes,set initial postion,and set color of node with AODV. Descr iption: In this program used to generate the nodes only there is no any other connection between the nodes. After creating the nam file and