搜索资源列表
X9C103
- 数字电位器X9C103的驱动程序。实现数字电位器的自动调节功能。
x9c103
- 本程序是基于51单片机的数字电位器的衰减，将三个数字电位器串着集连，可以步进一万份！-This procedure is based on 51 single-chip digital potentiometer decay, the three sets of string digital potentiometer connected, you can step ten thousand copies!
X9C103
- X9C102汇编及C语言调试应用程序,供参考.-X9C102,keil for X9C102 Software
X9C103
- x9c103的控制程序，我自己用过非常的好用，请多多的指教。- the descr iptio of the x9c103
MYx9c103
- 凌阳的数字电位器程序，适用于X9C103。DS1804经测试也通用。-Sunplus digital potentiometers program for X9C103. DS1804 has been tested and is also common.
51x9013
- 数字电位器x9c103的驱动,该驱动可以调高调低-Digital Potentiometers x9c103 drive, the drive can be increased to reduce
X9C103-
- 数字电位器，通过ad转换的值来调节显示的对比度以及电压电流 根据自己的需要来做调整，不能照抄-Digital potentiometer through the ad conversion value to adjust the display contrast and the voltage and current to make adjustments according to their needs, can not copy
X9C103
- 基于c8051f340对数字电位器x9c103的控制驱动程序-Based on the digital potentiometer x9c103 c8051f340 control driver
STC12C5A60S-and-x9c103
- 基于单片机STC12C5A60S2和数字电位器x9c103的测试程序,可结合正反馈放大电路实现可编程增益放大器功能-Microcontroller based digital potentiometer x9c103 STC12C5A60S2 and test procedures can be combined with positive feedback amplifier features programmable gain amplifier
change_wiper_X9C103
- Four AVR ASM routines for controling the wiper of a digital potentiometer type X9C103.
x9c103
- x9cXXX系列数字电位器，的相关资料和C程序代码-series x9cXXX digital potentiometer, and C code
69491732X9C103
- 数字电位器X9C103 步进控制 数字电位器向上调一步 数字电位器100个抽头，相当于99步-Digital potentiometer X9C103 stepping control
Signal-Generator
- 基于单片机的信号发生器，以单片机AT89S52为控制核心，ICL8038构成的震荡电路为总核心，高精度数字电位器X9C103构成精确调频调幅模块以及可编程键盘和液晶显示器模块构成的的数控及扫频函数信号发生器-Microcontroller-based signal generator, a microcontroller AT89S52 as the control core, ICL8038 oscillator circuit consisting of the total core, hi
x9c103
- x9c103数字电位器的驱动代码,已调试通过可正常使用-the x9c103 s drive code can be use.
X9C103
- X9C103数字电位器驱动程序（ 包含上调函数，下调函数，存储滑动端位置函数）-X9C103 digital potentiometer driver ( Contain raised function, reduced function, store the wiper position function)
X9C103
- PIC18F6621的10K数字电位器X9C103驱动程序，亲测通过！-PIC18F6621 of 10K digital potentiometer X9C103 driver by pro-test!
X9C103
- 利用51单片机和两个独立按键控制数字电位器X9C103的电阻输出，步进位100Ω。-The use of 51 microcontroller and two separate buttons to control the digital potentiometer X9C103 resistor output, step-bit 100Ω.
x9c103驱动程序
- 使用51单片机驱动的x9c103数字电位器(X9c103 digital potentiometer driven by 51 single-chip microcomputer)
X9C103数字电位器程序
- X9C103数字电位器程序 1111111111(X9C103 digital potentiometer program)
shuzidianweiqi
- arduino通过蓝牙手机端控制三路数字电位器x9c103，inc脚接D4，D7，D10，（控制级数），U/D脚接D3，D6，D9，（控制方向），CS脚接D2，D5，D8，（选择器件），本程序设定30步一次，可以根据需要自行调节，一共100步，如有不周之处还请指教。(Arduino through the Bluetooth mobile terminal control three digital potentiometers x9c103, Inc feet to D4, D7, D10,