资源列表
tunningPIDbyBGPSO
- 一款埃及学生用Matlab编的的基于PSO的PID整定程序，使用方法详见程序注释。-Tunning of PID controller using Bacterial Foraging Orientec by Particle swarm optimization My work has been accpepted in GECCO 2008 as Graduat Student workshop. I have used this techique in PID
HCS300DEMO
- HCS300 应用程序范例，稍作更改即可应用到其他项目-HCS300 example application, a little change can be applied to other projects
ledhzxs
- 以FPGA芯片为核心，扩展必要的外围电路，制作一个16*16LED点阵的汉字显示屏，使之能显示16*16LED点阵的汉字4个，如“一”，“二”，“三”，“四”等。要求显示的汉字无闪烁。每个汉字停留时间1秒。-To FPGA chip as the core, the expansion of the necessary external circuit, producing a lattice of 16* 16LED display of Chinese characters so that
ok
- 基于18f4550ICD2、16F877的PIC单片机烧写器仿真器ICD2制作源码 错误更正：877的RA4口要上拉一个5K电阻,R11<4R7,74hc07不行必须用74LS07 如果想重烧IC，4550的CONFIG请参考BMP文件 1。调试时最好有一个有保护的HUB，分步进行 2。焊好后，电位器旋到0，不插队IC，通电测各点电压，并调好12V 3。只插4550，连PC，应能发现新硬件，重点查晶体，USB电压， 4。插好所有I
EleGroupCtrl
- 一整套电梯控制器源程序，包含完整的CAN通讯协议源代码。-A set of elevator controller source code, complete source code for CAN communication protocol.
ds1302
- ds1302的说明文档，里面附有电路图，简单的程序接绍，好好看吧！-the instruction e-book of ds1302,include some typical circuit,and some programe!
Key8x8
- 64个(8x8)按键的矩阵键盘识别技术(利用Keil uVision2环境编写的)-64 (8x8) matrix keypad keys identification technology (the use of the environment prepared by Keil uVision2)
C51-ELEMETER
- LPC932设计的电表程序。完整的设计代码-LPC932 procedures designed meter. Integrity of the design code
CH372
- 本程序测试数据传输的正确性,可以用于长时间连续测试,基于MCS-51单片机C语言的示例程序,用于其它单片机时一般只要修改前面几个接口子程序及硬件定义-This procedure tests the validity of data that can be used for a long time for the test, based on the MCS-51 single-chip sample C language program, normally used for other sin
project
- 义隆单片机控制8个LED的渐明渐暗，并有一个按键控制流水灯的速度！-Elan single-chip control of the eight LED dimming out gradually, and there is a button to control the speed of light water!
Flash_ROM_lab
- 用SmartGen生成一个256*8的大小同步FIFO，并通过串口发送数据初始化FIFO。然后，再通过串口返回到上位机的串口调试程序显示，确认数据是否正确。-SmartGen generated with a size of 256* 8 Synchronous FIFO, and sending data through the serial port to initialize FIFO. And then back through the serial port to the PC ser
send
- 用C实现信号发生装置：1、正弦波：频率、幅度可调。 2、三角波：频率、幅度可调。 3、方 波：频率、幅度、占空比可调。 4、按键：波形切换、频率调节、幅度调节、方波占空比调节。 5、显示：信号的频率、幅度，在方波时还要显示占空比。 -Implementation using C Signal: 1, sine wave: frequency, amplitude adjustable. 2, triangle-wave: frequency, amplitude adjust