资源列表
IO_Test_NTC
- 这是一段利用单片机IO口作的温控程序,感温元件是NTC。功能是,当温度低过某值时开始加热, 随着温度上升。。。当高到某值时停止加热,然后开始冷却。。。不断重复。。。,使用时要注意 RC常数,常数过大会造成16位计数溢出,得不到正确结果。程序是作产品前的一个试验程序,当时 调试已通过,能作到±0.5℃。-This is a single-chip IO port for the use of temperature control procedures, temperature se
fm1702Code
- 为复旦微电子的射频芯片FM1702 SPI 源程序-Fudan Microelectronics for FM1702 SPI chip RF source
pwm
- 可以实现C8051F310的8位PWM输出-C8051F310 can achieve 8-bit PWM output
c51
- C51调试实验 跑马灯 变级调速跑马灯 声音报警 救护车声音输出 仙剑奇侠音乐输出-C51 debug-level variable speed control experiment Marquee Marquee ambulance voice alarm sound output仙剑Fairy music output
cf
- cf卡读写接口及源码-cf card reader interface and the source
32×16PointDisplay
- 笔者自己弄的一个32*16的点阵模块,使用51单片机以及74hc595和74hc138实现,内有动态显示程序和静态显示程序,以及Protel99SE原理图和PCB图.-I myself get a 32* 16 dot matrix module, the use of 51 single-chip, as well as 74hc595 and 74hc138 realized, there are dynamic display program and static display prog
GetSqrt
- 整形开平方程序 适用于各种单片机,本程序运行时间比查表要短,精度高,为精品程序-Plastic open square procedure applied to a variety of single-chip microcomputer, the program running time shorter than the look-up table, high precision, for the quality procedures
msp430C
- MSP430F44X系列的c代码 芯片为449,压缩包内有pdf文件,为原理图 其余文件夹为 flash读写,端口操作,基本定时器,LCD操作,键盘功能 五个文件夹。开发环境为IAR。代码均正确可运行,为学习msp430单片机的良师益友!-MSP430F44X series of c code chip for the 449, compressed packet, there are pdf documents, schematic diagram for the rest of th
M430F2274_embOS
- embOS的MSP430F2274移植版,在TI公司2274官方开发板上移植成功,并可以使用embView(任务管理器)进行观察。原embOS为三任务评估版,平台为MSP430F4691.-MSP430F2274 transplantation of embOS Edition, TI company in 2274 official development board transplant success, and can use embView (Task Manager) observat
89c2051
- 89c2051制造的绕线机程序,有电路图,有程序,程序已经调试好-89C2051 manufactured winding machine procedures, schematics, procedures, commissioning procedures have been good
time
- 三位数码管正计时程序,单片机T0定时器计时,Keil环境下的c语言程序。具有Proteus的仿真-The three digital control is time-process, single-chip timing T0 timer, Keil environment c language program. Simulation with Proteus
remote_control
- 基于AT89C52的16路无线防盗报警器 编程思路:设置定时器T0、T1两个中断子函数,分别用于计时和刷新显示屏。另外设置外中断0、1两个子函数,分别用于查询报警历史记录和响应无线电接收机收到的盗情信息。 主程序流程:依次调用按键扫描子函数、时间计算及转换子函数、报警处理子函数、定时输出判断子函数。-AT89C52-based 16-way wireless burglar alarm programming ideas: Set timers T0, T1 Functions t