资源列表
pcb
- PCB技术大全-protel元件封装库 及其详细的介绍了PCB的基本所用到的器件-PCB Book-protel technology package and its components in detail the basic introduction of the PCB used by the device
tunningPIDbyBGPSO
- 一款埃及学生用Matlab编的的基于PSO的PID整定程序,使用方法详见程序注释。-Tunning of PID controller using Bacterial Foraging Orientec by Particle swarm optimization My work has been accpepted in GECCO 2008 as Graduat Student workshop. I have used this techique in PID
HCS300DEMO
- HCS300 应用程序范例,稍作更改即可应用到其他项目-HCS300 example application, a little change can be applied to other projects
ledhzxs
- 以FPGA芯片为核心,扩展必要的外围电路,制作一个16*16LED点阵的汉字显示屏,使之能显示16*16LED点阵的汉字4个,如“一”,“二”,“三”,“四”等。要求显示的汉字无闪烁。每个汉字停留时间1秒。-To FPGA chip as the core, the expansion of the necessary external circuit, producing a lattice of 16* 16LED display of Chinese characters so that
ok
- 基于18f4550ICD2、16F877的PIC单片机烧写器仿真器ICD2制作源码 错误更正:877的RA4口要上拉一个5K电阻,R11<4R7,74hc07不行必须用74LS07 如果想重烧IC,4550的CONFIG请参考BMP文件 1。调试时最好有一个有保护的HUB,分步进行 2。焊好后,电位器旋到0,不插队IC,通电测各点电压,并调好12V 3。只插4550,连PC,应能发现新硬件,重点查晶体,USB电压, 4。插好所有I
EleGroupCtrl
- 一整套电梯控制器源程序,包含完整的CAN通讯协议源代码。-A set of elevator controller source code, complete source code for CAN communication protocol.
ds1302
- ds1302的说明文档,里面附有电路图,简单的程序接绍,好好看吧!-the instruction e-book of ds1302,include some typical circuit,and some programe!
Key8x8
- 64个(8x8)按键的矩阵键盘识别技术(利用Keil uVision2环境编写的)-64 (8x8) matrix keypad keys identification technology (the use of the environment prepared by Keil uVision2)
C51-ELEMETER
- LPC932设计的电表程序。完整的设计代码-LPC932 procedures designed meter. Integrity of the design code
CH372
- 本程序测试数据传输的正确性,可以用于长时间连续测试,基于MCS-51单片机C语言的示例程序,用于其它单片机时一般只要修改前面几个接口子程序及硬件定义-This procedure tests the validity of data that can be used for a long time for the test, based on the MCS-51 single-chip sample C language program, normally used for other sin
project
- 义隆单片机控制8个LED的渐明渐暗,并有一个按键控制流水灯的速度!-Elan single-chip control of the eight LED dimming out gradually, and there is a button to control the speed of light water!
Flash_ROM_lab
- 用SmartGen生成一个256*8的大小同步FIFO,并通过串口发送数据初始化FIFO。然后,再通过串口返回到上位机的串口调试程序显示,确认数据是否正确。-SmartGen generated with a size of 256* 8 Synchronous FIFO, and sending data through the serial port to initialize FIFO. And then back through the serial port to the PC ser