资源列表
Serial-Interface-test
- wince系统下，对系统串口的测试，有收发功能，C++编写-Wince under the system, a serial port to the system test, have to send and receive function, c++
HMIViewUser210
- 对wince平板一些功能的测试，如IO功能，蜂鸣器功能，定时功能，看门狗功能，-To wince tablet function tests, such as IO function, buzzer function, timing function, watchdog function, and so on
111
- 请认真书写上传资料的详细功能、包含内容说明(至少要20个字)。尽量不要让站长把时间都花费在为您修正说明上。压缩包解压-Please carefully write the details of the upload function, including the content descr iption (at least 20 words). Try not to let the webmaster to spend the time to amend the instructions for
adcPuart
- stm8s ADC+UART_HEX-OUTPUT
DSP-daima
- TMS320F280X型DSP直流电机控制，I2C，E2PROM等程序-TMS320F280X type DSP DC motor control, I2C, E2PROM and other procedures
OBD_CAN
- 用STM32F103单片机做的汽车OBD诊断仪，可以读取整车CAN线上，汽车发动机转速，车速等信息，对CAN通信学习有一定帮助，本代码支持所有标准CAN车型。-STM32F103 microcontroller to do with car OBD diagnostic, read the vehicle CAN line, automobile engine speed, vehicle speed and other information, to learn some help CAN c
STM32__MPU6050__Kalman
- 以stm32f103rct6为例，通过串口通信，调试MPU6050数据，检测X轴加速度，Y轴角速度，并应用卡尔曼滤波器处理MPU6050数据。-In stm32f103rct6 example, through serial communication, debugging MPU6050 data, detects X-axis acceleration, Y-axis angular velocity, and the Kalman filter process MPU6050 data.
51_uCOSII
- 基于51移植uCOSII系统(仅供参考，欢迎志同道合的朋友共同研究)。-Based on 51 transplant uCOSII system (for reference only, welcome like-minded friends to study)
MP3_51_and_VS1003
- 用STC51单片机和VS1003制作的音乐播放器，包含电路和源码。-With STC51 microcontroller and VS1003 making music players, including circuit and source code.
power-circuit
- 在电源输入的前端利用旁路去耦电容滤波器，在+12V输入时，首先通过一个电解电容C1和电容C2保证电压的输入稳定，之后选择利用稳压器NCP1117ST50T3G将输出电压降到+5V，如图3.5所示，其输出电流为1A。在稳压器之后继续采用一个电解电容C3来保证输入到芯片的供电电压稳定。-Power input at the front end of the use of bypass decoupling capacitor filter when+12V input through a first
communication-circuit
- 由于RS232的电平与Arduino Mega 2560的接口电平不能兼容，所以就需要进行电平的转换，即进行串口转换模块的设计，本文选择利用ATMEGA16U2-MU模块来做电平转换，将上位机的指令通过此模块发给下位机-Since the RS232 level is not compatible with the Arduino Mega 2560 interface level, so we need to level conversion, that is designed to seri
core-circuit
- ATmega2560通过USB接口与PC进行传输，供电电压为5V，内部晶振为16MHz。该芯片共有有54个I/O引脚，特别适用于需要大量I/O口电路，其中的16个可以提供脉宽调制（PWM）模拟输出，还有另外16个模拟输入引脚。在通信方面，有4个硬件串口，另外也可以支持SPI通信和I2C/TWI设备。设计核心电路中加入复位按键，通过USB串口进行通信。-ATmega2560 through the USB interface with the PC for transmission, power