资源列表
3-button-control-LED-light-off
- 掌握按键的使用，实现人机交互，按键控制LED亮灭。-Master the use of buttons to achieve human-computer interaction. Button control LED light off
usb_host_device_verilog
- USB-host-device控制模块的设计参考，对于初学者可以以此为参考进行设计，代码可在仿真软件中验证（modelsim、VCS等）。-USB-host-device control module design reference for beginners can be used as a reference design, the code can be verified in the simulation software (modelsim, VCS, etc.).
buttons-control-the-LED-Marquee
- 按键控制LED跑马灯,读取按键状态,设置 LED 灯相应的 IO 口,设置按键 S1 相应的 IO 口, 扫描按键当前状态,按下时执行跑马灯效果.-The control button LED marquee, read the key state, set the corresponding LED lamp IO port, IO port settings button S1, Key scan the current state of implementation of the
ubuntu14.04_Embedded-environment
- 在嵌入式开发中基于14.04版本ubuntu常用环境的搭建以及ubuntu一些常规设置，如nfs、tftp、网络设置等，文档中有详细目录，不同版本的ubuntu可能会有些许出入，但一般问题不大-In the embedded development based on the 14.04 version of ubuntu common environment to set up and ubuntu some conventional settings, such as nfs, tftp, n
51_test
- 适合初学者学习51单片机时参考的代码，一共有7份代码。 1.最简单的点亮LED灯到实现流水灯效果 2-7.点亮数码管-数码管模拟显示时间-轮询机制实现按键调节时间-使用中断控制时间 代码有我练习时从简单到一步步增加功能的过程，希望能帮到初学者 - Suitable for beginners to learn 51 SCM reference code, a total of 7 code. 1. The most simple light LED lights
QT_linux
- 本文档详细描述了在怎么把QT移植到ubuntu系统中并一步步搭建好QT环境，前面稍微提到了我在cortex-A8内核的开发板上的过程，不适用的可以直接看后面的QT移植即可- This document describes in detail how the QT ported to the ubuntu system and build a good QT environment, slightly mentioned in front of my development board in
esp8266_wifi
- 在51单片机上外接一个esp8266 wifi模块，实现手机连接模块产生的wifi，通过APP向单片机发送控制命令。该代码实现了简单的控制LED灯的亮灭。- 51 in a microcontroller connected to a esp8266 wifi module to achieve cell phone connection module to produce wifi, through the APP to send control commands to the micro
GprsA8500
- 这是一个关于GPRS模块A8500的驱动程序。-This is a GPRS module A8500 on the driver.
offsetof
- 解析内核中的offset代码，通过结构体成员地址反获取结构体地址从而可以操控整个结构体，深化对指针的理解，有些面试题中也可能会遇到这种情况-翻译 关闭即时翻译 Parsing the offset code in the kernel, through the structural member address anti-obtain structural address which can manipulate the entire structure, deepen the unde
wifi_esp8266
- 在51单片机上外接一个esp8266 wifi模块，实现手机连接模块产生的wifi，通过APP向单片机发送控制命令。该代码中只实现了简单的控制LED灯的亮灭。- 51 in a microcontroller connected to a esp8266 wifi module to achieve cell phone connection module to produce wifi, through the APP to send control commands to the mic
SPI_SD_CARD
- 使用sopc系统，结合nios软件，实现sd卡的读写，学习FPGA编写的过程-Use sopc system, combined with nios software, sd card reader, prepared by the process of learning FPGA
DS18B20
- 用stm32f103芯片处理温度传感器DS18B20-Using stm32f103 chip processing temperature sensor DS18B20