资源列表
sensor-openloop
- DSP2812控制无刷直流电机的开环控制- 22/5000 DSP2812 kòngzhì wú shuā zhíliú diànjī de kāi huán kòngzhì chéngxù DSP2812 control of brushless DC motor open loop control procedures
DemoMPC5646_GPIO
- 基于MPC5646CF0MLU1单片机的GPIO输出控制程序-GPIO Output Control Program Based on MPC5646CF0MLU1 Single Chip Microcomputer
AVR336
- AVR336: An ADPCM encoder is needed to produce the packed files for the decoder described in this application note. The decoder will decode data, which has ben packed with any standard-compliant ADPCM encoder but in order to obtain highest possibl
ATMEL-AVR336.doc2572.pdf
- AVR336: ADPCM Decoder • AVR Application Decodes ADPCM Signal in Real-Time • Supports Bit Rates of 16, 24, 32 and 40 kbit/s • More Than One Minute Playback Time on ATmega128 (at 16 kbit/s) • Decoded Signal Played Using T
LS53C
- LS53C是采用新型的发明专利技术L体系结构技术实现了多核并发处理引擎,支持同时并 发地执行三道程序(相当于有3个独立的内核),且均能以最高40M主频同刻并发的执行。-LS53C is a new type of invention patented technology L architecture technology to achieve a multi-core concurrent processing engine to support the same time and M
dps
- 数字移相,STM32单片机,采用ad采集信号经处理后da输出-Digital phase shift, STM32 microcontroller, using ad to collect the signal after processing da output
AD7606FSMC
- 该程序是一款基于STM32F407VGT6的数据数据采集卡的驱动程序,采用16位,2000ksps采样率的ADC芯片-AD7606,通过8个AI通道彩技术数据,利用MODBUS协议实时回传给上位机软件-The program is based on the STM32F407VGT6 data acquisition card driver, using 16-bit sampling rate of 2000ksps ADC chip-AD7606, 8 AI channel, the col
pcb
- NYGNNQ的PCB和SCH文件,RF模块选择用低成本的NRF24L01,mcu选择用国产的单片机stc15w401as和stc15w408s,-NYGNNQ PCB and SCH files, RF module selection with low-cost NRF24L01, mcu choose to use the domestic single-chip stc15w401as and stc15w408s,
control-GPIOA-all-pin
- 控制STM32f407ve-GPIOA所有引脚电平变化-control stm32f407ve-GPIOA all pin vol changeable
FFT
- verilog xilinx IP实现FFT仿真-Verilog xilinx IP implementation FFT simulation
MA801_MA802_Datasheet_A10
- 台湾 MEGAWIN 公司的8051单片机使用手册,写的很详细,适合开发者参考,中文版的-Taiwan MEGAWIN 8051 single-chip user manual, written in a very detailed, suitable for the developer reference, the Chinese version of the
PowerSum
- 此模块的主要功能是实现距离单元数据的功率和求解,即把输入信号的实部、虚部分别 求解平方和,然后把两者相加,每个距离单元内有1024个复数数据 接口: clk 时钟信号,50MHz rst_n 复位信号,低电平有效 PowerSumInEn:功率和模块输入信号的有效信号,1bit,高电平有效 PowerSumInRe:功率和模块输入信号的实部,8bit PowerSumInIm:功率和模块输入信号的虚部,8bit PowerSumOut: 功率和模块输出