资源列表
ButtonA-sends-a-byte-temperature
- 通过CAN总线将该节点采集的温度数据发送出去 CAN总线环境温度采集 按键控制发送 IDE环境： keilC CAN_ Send: CAN发送子程序,查询发送 CAN_Receive：CAN接收子程序，中断接收 硬件连接： AT89S51/52+MCP2515+DS18B20-Temperature data sent via the CAN bus node collection CAN-bus controlled ambient temperature ac
CAN-receive-8-bytes-forwarded
- 通过CAN总线接收八个字节数据在转发发出去 CAN通信测试程序，CAN中继器的功能 2515初始化程序 CAN接收子程序，中断接收 AT89S51/52+MCP2515-Receive eight bytes of data via CAN bus sent to the forwarding CAN communications test program, CAN repeater function 2515 initialization procedure
msp430g2553
- msp430g2553定时器的应用代码程序，实现led灯闪烁-msp430g2553 timer
MC9S12XS
- S12单片机的资料 《MC9S12XS单片机原理及嵌入式系统开发》 -S12 MCU Data " MC9S12XS SCM principles and embedded systems development."
AD9854_MSP430_jiance_fudukey4
- 基于430单片机实现的AD9852信号发生器。可以实现键盘输入频率选择，也可实现频率范围内扫频，功能菜单由12864显示-the AD9852 signal productor based on 430 MCU ,the frequency of signal can be controled by 4*4 keyboard .
AD7705andTemperature-Sampling
- 1、读取AD7705输出电压值U 2、根据PT1000阻值计算温度 -A read AD7705 output voltage U 2, according to the calculated temperature resistance PT1000
Radio1.0.10
- CVAVR ATMEL 单片机开发的 驱动1846芯片的 车载收音机 商用程序。-1846 CAR RADIO
cc2530-LCD12864-display-program
- TI的ZigBee cc2530芯片的12864LCD显示程序 串口驱动方式仅占用5个IO-TI ZigBee cc2530 chip 12864LCD only way serial driver display program with five IO
wxaj2013_Datasheet
- C语言写的电容式触摸键盘代码，稳定可靠，不受环境温度温度影响，也不受人体静电或者交流电感应影响 采用wxaj2013包含电路和手册 功能说明： 按下触盘K1 led1亮，再按一次led1灭，按下生效，弹起或长按保持 K2,K3,K4的功能也一样。本程序支持K1,K2,K3,K4同时独立操作-Written in C language code capacitive touch keypad, reliable, free from ambient temperature tem
Digital-potentiometer-adjustment
- 此程序是基于stc单片机的控制数字电位器MCP41010的程序，并带有protues仿真图。-This procedure is based on stc microcontroller MCP41010 digital potentiometer control procedures, and with protues simulation Fig.
2.2inch-TFT-Display-c51
- 此程序是基于stc单片机的2.2寸串口屏的控制程序，驱动芯片为ILI9341.-This procedure is based on stc SCM 2.2-inch screen serial control program, driver chips for ILI9341.
AIR0036A9
- ht46f47e程序,应用于空气净化器，控制鼓风机-AIR clear