资源列表
dfghjklk
- 阐述传统直接转矩控制系统转矩脉动的缺点，本文将空间矢量脉宽调制技术引入永磁同步电机的直接转矩控制系统中，利用空间矢量的调制过程，可在相同的系统硬件条件下得到更多的、连续的电压空间矢量，进而得到对电机更准确的控制。仿真结果表明，该方案既保持了直接转矩控制快速动态响应，又减小了电机转矩的脉动。- permanent magnet synchronous motor and elaborates the impact of space voltage vector of the stator flux
SD
- 基于SVPWM的永磁同步电机直接转矩控制系统框图如图1所示，其中参考电压空间矢量估计器和SVPWM 单元替代了传统控制方式中的定子磁链、电磁转矩滞环控制环节和开关表。-lux and the electromagnetic torque.Secondly, the paper introduces direct torque control of permanent magnet synchronous motor SVPWM technology.Under the same hardwar
lab1-GPIO_LED
- TMS320F28335 DSP GPIO 跑马灯应用实例-TMS320F28335 DSP GPIO
ad5457s
- 基于TMS320VC33的DSP 带有低通滤波器算法的AD采集程序。-AD-based acquisition program TMS320VC33 of DSP algorithms with a low-pass filter.
slip_frequency_control
- 自己编的异步电机转差频率控制，逆变器svpm算法，转速码盘是1024，读者可以自己根据自己情况改变-Their series induction motor slip frequency control, inverters svpm algorithm, speed encoder 1024, readers can change according to their own circumstances
close_loop
- 伺服电机，闭环控制。包括DSP28335的系统初始化，AD的初始化，速度、位置的计算等-server motor,close-loop controller.it includes the inition of DSP 28335,inition steps of ad programe and the process of motor s speed and postion calcult.
moto-close_loop_control
- 用DSP2812实现伺服电机的闭环控制，包括.h文件.c文件，及DSP系统的初始化。-ues DSP 2812 to realize the close-loop of server motion control.the file includes .h&.c file.Also describle the inition of DSP.
ctom_ipcdrivers
- F28M35 双核处理器的程序 C28核与M3 核的通信-F28M35 dual-core processor program
3DP_dialog
- 3D打印机调用gcodeviewer并打印，友好性比较好-3D printers and print call gcodeviewer friendship is better
Example_281xECanBack2Back
- DSP2812 CAN总线 无中断例程源码，包括发送和接收-2812 CAN bus without interruption routine,
SRM_Motor_1
- 这是一个以DSP28035为平台的开关磁阻电机调速控制程序。可实现开关磁阻电机的平滑调速，并能准确显示实际转速。-This is a DSP28035 for the switched reluctance motor drive system control program. Can realize smooth speed control of switched reluctance motor, and can accurately display the actual speed.
SCI
- DSP28335对SCIB和SCIC同时工作，互不影响，调试通过,用ccs3.3调试的-DSP28335 and SCIC work simultaneously on the SCIB, independently of each other, debugging, debugging with ccs3.3