资源列表
TASM5andborland4.5
- 包含了用borland c++ 4.5调试用的TASM软件与UCOS_II可用源码，并且有移植UCOS_II到X86 PC上之图文版的具体方法-Included with borland c++ 4.5 debug TASM used UCOS_II available software and source, and transplant to UCOS_II graphic on a X86 PC version of the specific methods
uC-Serial
- SERIAL (BYTE) COMMUNICATION MODULE for UCOS. Port: AT91SAM9RL.-SERIAL (BYTE) COMMUNICATION MODULE for UCOS. Port: AT91SAM9RL.
uCOS_II_business_Full_Code
- uC/OS-II完整商业版源代码包含了GUI和FS-uC/OS-II the full commercial version of the source code contains a GUI and the FS
ucos-commercial-version
- ucos的商业版本，相对稳定的嵌入式操作系统-ucos a commercial version,
Ethernet_KSZ8041NL
- LPC2300 网络驱动 KSZ8041NL-LPC2300 Network Driver KSZ8041NL
ucosII_source
- 熟悉嵌入式实时操作系统μC/OS-II原理及特点； 选择适用于μC/OS-II的文件系统，并实现之； 掌握SQLite嵌入式数据库的原理； 完成SQLite数据库在μC/OS-II下移植； 编写应用程序，以证明数据库移植后的系统可用性；-failed to translate
ucosII lpc1114
- LPC1114uCOSII是uCOSII在LPC1114芯片上的移植，由于LPC1114内部空间有限，故进行了一些裁剪，但整个系统功能完善。-LPC1114uCOSII is uCOSII transplantation in LPC1114 chip, due to LPC1114 internal space is limited, it made some cutting, but the entire system fully functional.
uCOS-II-2.5
- uCOS-II 2.52中间件I2C\SPI\UAR0-uCOS-II 2.52 middleware I2C \ SPI \ UAR0
RTOS_MDK--uCOS-II-for-STM32(LCD5110)
- RTOS_MDK uCOS-II for STM32（LCD5110)意法半导体cpu移植的uCOS2.52，诺基亚的LCD5510显示器，效果直接显示，很符合刚学uCOS系统的同学。-RTOS_MDK uCOS-II for STM32 (LCD5110) STMicroelectronics cpu transplant uCOS2.52, Nokia' s LCD5510 display the results directly show that the system is con
dsPIC33FJ256GP710A
- dsPIC33 UCOS sPIC33 microchip dsPIC UART
NUC950_uCosII
- nuc950处理器的ucos移植，已移植好，针对nuc950开发板。-The nuc950 processor uCOS transplantation Transplantation, has been good, according to the nuc950 development board.
STM32PUCOS-II=GPIO_PS2_TIM
- 1.板上的8 个按键分别 代表数字1-8，按下一个按键将结果通过串口发送到PC机上显示； 2.使用两个定时器模块，分别定时为1ms 和100ms 产生中断，使用它们分别 产生1s的定时时间，将时间分别显示到数码管上； 3.外接PS/2小键盘，将按键的值通过串口显示到PC机上。-A panel of eight key representing the number 1-8 press a key the results sent through the serial port on