资源列表
SerialApp_Coordinator-Device
- zigbee无线通信协调器源码，基于Z-STACK，通过串口，动态显示网络状态，实现数据收发功能。-zigbee wireless communications coordinator source, based on the Z-STACK, through the serial port, dynamic display network status, send and receive data functions.
automatic-trace-program
- 基于STM32小车自动循迹程序,是用超声波传感器来检测，差动驱动的方式来行走。PWM驱动电机。-based on STM32 of automatic trace car program,it is to use Ultrasonic sensors to detect, differential drive way to walk. PWM drive motor.
AN148
- AMBA Application Note: AN148 - Using EB with CT7TDMI, CT926EJ-S, and CT1136JF-S Core Tiles.-AMBA Application Note: AN148- Using EB with CT7TDMI, CT926EJ-S, and CT1136JF-S Core Tiles. This example shows how to use the EB baseboard with CT7TDMI, CT92
P89V51
- 里边涵盖了P89V51单片机制作中的一些程序，非常关键-The inside covers P89V51 microcontroller production procedures, it is critical
eos_examples
- 嵌入式操作系统WinCE.net及开发应用-大连理工的实例源代码-WinCE.net Embedded operating system and application - Dalian Polytechnic example source code
robot
- STM32机器人控制，通过上位机控制，此程序仅仅包含下位机，运行环境为stm32103系列芯片，4.53SDK-STM32 robot control
PLAN2408-2006-03-31
- 电子词典源码,开发环境为TURBO C++ 3.0-Electronic Dictionary Source
Phone1.0_SRC
- s3c6410开发板 测GPRS模块的源码一、测试AT指令 1） 启动开发板(用户将会看到GPRS同时启动，LED灯闪烁），进入WINCE界面，点击“我的设备”进入，看到WINDOWS文件夹点击进入，将会看到“SerialPort”, 双击打开； 2） 出现SerialPort 串口菜单，然后点击齿轮图样的按钮进行设置，GPRS 串口号 设置为COM2,波特率设置为9600，其它不用设置，然后点击确定； 3） 在刚才的SerialPort 串口菜单上输入AT指令（
EDA
- vhdl语言编写的交通灯。有程序有电路图。-The VHDL language the traffic lights. There is a program to the circuit diagram.
10.开发板配套C实验例程100多个
- 里面有计时器，秒表，钟表，步进机，温度计，密码锁，门铃，报警器等常见100多个例程(There are more than 100 routines: timer, stopwatch, clock, stepper, thermometer, password lock, doorbell, alarm and so on.)
TR4_GPIO1_D8M
- 友晶科技的TR4的开发板，接上D8M摄像头的程序 输出的是MIPI解码后的10位数据 内带signaltap仿真结果和连接图(The development board of TR4, the D8M camera program. The output is the 10 bit data after MIPI decoding. include signaltap simulation results and connection diagrams)
Jlink固件更新-恢复及Jlink4.9驱动4.9
- Jlink固件更新-恢复及Jlink4.9驱动4.9(Jlink firmware update - recovery and Jlink4.9 drive 4.9)