资源列表
tx
- 通信协议: 第1字节,MSB为1,为第1字节标志,第2字节,MSB为0,为非第一字节标志,其余类推……,最后一个字节为前几个字节后7位的异或校验和。 测试方法:可以将串口调试助手的发送框写上 95 10 20 25,并选上16进制发送,接收框选上16进制显示,如果每发送一次就接收到95 10 20 25,说明测试成功。 //这是一个单片机C51串口接收(中断)和发送例程,可以用来测试51单片机的中断接收 //和查询发送,另外我觉得发送没有必要用中断,因为程序的开
UART
- pic30f4012异步串口调试程序,与pc的通信程序-item program for UART of pic30f4012
LCDC
- 基于AT89C51的LCD1602显示程序-The LCD1602 display program based on AT89C51
12864test
- 12864液晶屏的简单测试程序~~显示的是一首诗,分四行显示-12864 LCD screen a simple test program ~ ~ shows a poem, four lines show sub-
led
- 数码管跑表,从000到999历时十秒,按下S1,hold on-Digital control stopwatch, from 000 to 999 last 10 seconds, press the S1, hold on
msp430f437ADC
- TI公司 MSP430F437单片机ADC模块初始设置程序-TI MSP430F437 MCU ADC module initial company setup program
shangweiji
- 利用vb6.0编程软件制作简单的上位机程序,实现与单片机的穿行通信-Using vb6.0 programming software to create a simple PC program, to achieve walking through communication with the MCU
1602
- 1602液晶的的操作C文件,有注释,适用与AVR单片机-1602 LCD operation C file, there are notes for AVR microcontroller with
quangda
- 同时按键抢答,先按的键有效,其他按键锁死 复位后重新开始抢答-Button to answer in the same time, press the keys on the other lock reset button to restart Responder
eeprom
- ATMEGA16单片机的EEPROM部分代码,-ATMEGA16 microcontroller' s EEPROM part of the code,
8253jishuqi
- 用8253对标准脉冲信号进行计数,就可以实现定时功能。用板上的1MHz作为标准信号,将8253可编程计数器/定时器的时间常数设在1000000次,就可以在定时器的管脚上输出1秒针高/1秒钟低的脉冲信号。因为8253每个计数器只有十六位,要用两个计数器才能实现一百万次的计数,实现每一秒输出状态发生一次反转。-With 8253 pairs of standard pulse counting, timing can be achieved. 1MHz with the board as a sta
liushuideng1
- 本实验中主要应用单片机的端口操作及延时(通过每条指令执行时间来延时)循环程序。首先需要知道如何让一个发光二极管工作,当在它的A和K两个电极加上合适的电压的时候,它就会亮起来。-In this study, the main application microcontroller port operations and delay ( delay) of each instruction execution time cycle program . First need to know how t