资源列表
uart_test_msp430
- This a simple hardware UART test program. It receives text lines over the serial port and writes back a status msg with length and contents of the buffer.-This a simple UART hardware test program . It receives text lines over the serial port and
tcpipformsp430
- An example of TCP/IP stuff on msp430, taken from slaa137.pdf.-An example of TCP / IP stuff on Constrictor. taken from slaa137.pdf.
robotgoat
- 本程序是本人毕业论文时设计的，是在MAPLE环境下，用PIC16F87X汇编写的，功能是实现用单片机控制一个小型机器人的动作-I Graduation design, in the Maple environment, PIC16F87X compilation was made by the functional MCU is used to control a small robot movements.
c8051fxxxlcd
- c8051f单片机液晶点阵显示 -128*64,控制器KS0108 试验准备:将拨码开关S1和S2置于ON位置. 运行此程序,LCD将交替显示\"换代创新后的51-高速SOC美国CYGNAL 8051F\"\"新华龙电子-单片机推广应用急先锋!\",\"汉字\".-c8051f SCM LCD dot matrix display -128 * 64, Controller KS0108 test preparations : dial-Switch S1 and S2 placed
c8051f020timerLCD
- 目标器件: C8051F02x 编译工具: Silicon Laboratories IDE 程序说明:此程序首先对时钟芯片写入初值，延时后再读取时钟值，并年，月，日，时，分，秒分别显示在LCD屏上。 -target Components : C8051F02x compiler tools : Silicon Laboratories IDE procedures : This procedure first right into the initial clock chip, c
c8051f020key
- 目标器件: C8051F02x 编译工具: Silicon Laboratories IDE 程序说明: 此程序动态扫描键盘，当有按键按下时，将此键转换成对应的数字键值，同时蜂鸣器响一声-target Components : C8051F02x compiler tools : Silicon Laboratories IDE procedures Note : This procedure dynamic scanning keyboard, When a button press,
c8051f020led
- 此程序用于测试教学实验机c8051f020的LED数码管示，程序运行时LED将轮流点亮，显示从0到9之间的数字。-this procedure for testing experimental aircraft C8051f020 teaching LED digital control said, procedures will be carried out when the LED lights, shown from 0-9 between the figures.
c8051f020StepMotor
- StepMotor此程序通过c8051f020I/O口驱动步进电机-StepMotor this procedure c8051f020I / O Stepper Motor Driver
c8051f020lcd
- 这个程序可以在该液晶模块上显示二行字符:Welcom To NCD，www.xhl.com.cn 此程序用8位数据线来驱动液晶-this procedure can be in the LCD displayed on two Character : Welcom To NCD. www.xhl.com.cn this procedure with eight data lines to LCD Driver
c8051f020red
- 程序接收红外发射过来的数据，接收解码后由CPU读取,程序运行前将S2都拨到ON.J17短接第一和第二脚。 -procedures for receiving infrared fired up the data after receiving decoders read by the CPU. pre-operational procedures will have to transfer S2 ON.J17 shorted the first and second legs.
fpgacaiji
- 自己课程设计写的程序，用FPGA控制ADC0809的转换时序来完成模/数转换，然后将转换完的数字信号传递给0832-write their own curriculum design process, Connection between ADC 0809 FPGA control the timing to complete the conversion analog / digital conversion, End then converting the digital signal to
164SPI
- 单片机编程，直流电机单极性双闭环PWM控制程序-microcontroller programming, Motor Unipolar double-loop PWM control procedures