资源列表
minirisc.tar
- 嵌入式操作系统的基本输入输出程序，支持多种硬件平台，集成网络支持-Embedded operating system's basic input-output process, support for a variety of hardware platforms, integrated networking support
S3C2410LED
- ARM920T SamsungS3C2410平台下 LED测试程序 通过烧入Flash来执行引导程序，以点亮开发板上的LED来获得运行结果，是用来调试的最基本工具与手段。-ARM920T SamsungS3C2410 platform LED testing procedures into burning through F. lash guide to the implementation of procedures to light up the development of the
PID_Arithmetic
- PID.c 新型PID控制及其应用 先进PID控制及其MATLAB仿真 STEP7中PID控制的实现方法.-PID.c New PID control and the application of advanced PID control and its MATLAB STE P7 PID control method.
duodzdq
- 单片机的简单应用,下载后既可执行,实现多灯震荡的功能-SCM simple application can download implementation, multi-functional light concussion
advdrvrpci
- pc机上经由pci连接的ata和atapi设备驱动，包括dma和pio模式-pc machine connected via pci was observed atapi device drivers, including dma and pio mode
mindrvr
- ata和atapi的驱动程序，包括pio和dma传输方式。-was observed atapi drivers, including pio dma and the means of transmission.
led_da_drivers
- 华颐公司的以AT91RM9200为CPU的9200F 开发板在linux开发环境下的(不是基于ADS) LED,和DA驱动和测试程序的源代码-Chinese companies to AT91RM9200 9200F to the CPU board development opened in linux the environment (not on ADS) LED, and the DA-driven and test procedures source code
D_f_apparatus
- 频率测量和周期测量的基本方法是采用以固定时钟作为参考时钟，分别测量单个周期的计数为周期，单位时间的计数为频率。但是由于被测信号的频率不同，测量精度会发生变化，采用低频测量周期，高频测量频率，然后分别求倒数，便可得到对应的频率和周期-frequency measurement and measurement cycle is the basic method used to a fixed clock as a reference clock, measured single cycle to c
D_Clock
- 数字钟的主要功能有年月日时分秒的显示输出功能和对日期及时间进行设置的功能，还可以有整点报时等功能。设计数字钟的核心问题是时钟日期的自动转换功能。即自动识别不同月份的天数的控制。据此可以设计一个如图１所示结构的数字钟，该数字钟包括校时模块、时分秒计时模块、年月日模块、和输出选择模块。-digital clock is the main function Minutes date when the output function and the date and time set for the f
9
- 此源码事有关DSP编程用的，欢迎使用，希望有更多的源码上载 -this matter the source of DSP programming welcome to use, I hope there will be more on the source
jqereresrer
- 计算一组序列的游程数（序列长度为16），并在数码管上显示，用89S51实现-calculated a sequence of run-length (the length of the sequence of 16), and the digital pipe, used devised to achieve
cesffffsfesfesf
- 产生级数为4的M序列，P1输入4个初值，在数码管上显示出来，单片机模拟产生伪序列码-produce series for the M-4 sequence, P1 four initial input, the digital control on the show. SCM simulation of pseudo-sequence code