资源列表
yinyue
- 一个单片机做的电子发音台历，可以发出１２支曲子-a microcontroller to do electronic pronunciation desk, can be issued 12 song
zlg7290_c51
- 51单片机 zlg７２９０数字钟，iic总线协议，是学习５１单片机模拟iic总线协议的最好选择．-51 SCM zlg7290 digital clock, Head bus protocol, MCU 51 is learning simulation 2005/09 Bus Protocol best option.
can-test3
- 44B0X的CAN总线实验，CAN总线应用十分广泛，希望能对各位以后的CAN总线的开发有帮助，可以有个参照-44B0X CAN bus experiment, CAN very broad application, The hope is to you after the CAN bus of development assistance, can be a light
loaducos
- UCOS移植到44B0的原代码，对初学UCOS者有一定的帮助，希望细细品味，总结一下，肯定收获不小。-44B0 UCOS transplanted to the original code, UCOS for beginners who have some help, hope careful look, in summing up, and certainly learned a lot.
D12+DSP6711
- D12+DSP6711固件程序源码。解压缩后包含两个文件。希望对大家有帮助。-D12 firmware source. After extracting two documents contain. We want to help.
TMS320C6000BootMethod
- 首先介绍了DSP/BIOS的优点，然后讨论了DSP/BIOS的资源优化方法，最后介绍了使用DSP/BIOS编程时的自举引导方法。-first introduced the DSP / BIOS advantage then discuss the DSP / BIOS resource optimization method, Finally, the use of DSP / BIOS programming at the Boot Method.
ARMProgramTecgniques
- 学习ARM编程的好书，包括汇编和C语言编程，并讲述了ARM的架构，-learning programming books, including the compilation and the C programming language, and on the ARM architecture,
concorr
- 计算如序列x[k]={1,2,3,4,5}与序列h[k]={2,-2,3,5}的卷积本程序是和互相关的C源程序。-if the calculation sequence x [k] = () 1,2,3,4,5 and sequence h [k] = (2, ,3, 5) of the deconvolution procedure is inter-related to the C source.
board123
- 1 本程序为DSK板的初始化过程。 2.当DSP的主时钟频率为50MHz时，计算锁定时间定时器PLLCOUNT的值，并修改相关程序。 3.将主时钟的频率分别设置为50MHz、20MHz、10MHz、5MHz，通过观察LED指示灯的闪动频率来验证程序运行是否正确。-a procedure for DSK board initialization process. 2. When DSP master clock frequency of 50MHz, calculation time lo
WinBand_VCD_Source
- 找了好多地方，终于找到了华邦VCD完整C51代码，对做DVD编程控制有一定的参考价值。-find a lot of places, finally found a VCD complete Winbond C51 code, the DVD programming done to a certain extent control the reference value.
cosinexp123
- 1.分别利用计算法和查表法产生1000Hz的余弦波信号，并使用示波器观测产生信号的频率和幅度。 2.利用计算法产生其他非正弦类周期信号波形，如周期矩形波、三角波、锯齿波等。-1. Each calculation method and the use of look-up table method have 1000Hz the cosine wave signal, Oscilloscope observation and the use of the generated signal f
TIMER123
- 1.可组合给定内容的程序，利用示波器测量XF或LED0管脚的信号频率。 2.可修改定时器中断服务程序，使三个发光极管每隔1秒钟轮流点亮一次。-1. Portfolio will be content to the procedure, and use oscilloscope measurement XF or LED0 pin signal frequency. 2. Amend timer interrupt service routine, three-top every one li