资源列表
W78E516B-BootLoader
- W78E516B的BOOT程序,将该程序烧写到BOOT区,当启动到BOOT区时,可以通过该程序经串口将系统程序下载到主程序区,晶振为22.1184MHz时波特率可以达到115200bps,比常规烧率器都快!-W78E516B the BOOT process of burning of this program BOOT, When the boot BOOT areas, through the program as a serial port to download system main
93c06
- SPI总线驱动程序 包括的普通封装标准模式,特殊封装标准模式 默认11.0592Mhz的晶振。-SPI bus driver package including the general standard model, special Packaging standard default mode 11.0592Mhz the crystal.
8051jing
- 8051进行8路LED模拟分支控制用8051的P1口作为输入、P0口作为输出,通过74LS244接8路LED模拟分支控制-8051 for 8-way analog LED branch controlling the P1 8051 as input mouth, P0 mouth as output, then eight road 74LS244 LED control simulation branch
93c06jing
- SPI总线驱动程序 包括的普通封装标准模式,特殊封装标准模式默认11.0592Mhz的晶振-SPI bus driver package including the general standard model, special Packaging standard default mode of crystal 11.0592Mhz
1520
- 122x32液晶1520控制器驱动程序 [最后修改时间] 2003年5月12日 [版权所有] 哈尔滨众邦龙科技开发有限公司 [12232资料] 请到www.mcuzb.com下载 -1520 122x32 LCD controller driver [last modified in 2003, May 12 [Copyright] Harbin Zhongbang Lung Technology Development Company [12,232] free www.mcu
c51jing
- 实现pc机键盘(p/s2接口)与8位单片机连接使用 原理:键盘时钟接在p3.2口,既8051的外部中断int0上,键盘数据接到p1.0上 每次按键,键盘会向单片机发脉冲使单片机发生外部中断,数据有p1.0口一位一位传进来 传回的数据格式为:1位开始位(0),8位数据位(所按按键的通码,用来识别按键),1位校验位(奇校验) 1位结束位(1) 实现:将键盘发回的数据放到一个缓冲区里(数组),当按键结束后发生内部中断来处理所按的按键 缺点:由于51单片机的容量有限所以缓冲区不可
new_zlg_2104_20048585137371
- 周立功的 51单片机的UCOS嵌入式系统源代码, 完整编译,具有使用例子-Jan 51 weeks of UCOS embedded microcontroller system source code, compile complete with usage example
FS2518
- 福建 赛福 刻板机 FS2518 软件 实用不过有点小复杂 -Fujian-fu stereotypes practical software for FS2518 But a little complex
用PDIUSBD12和K9F5608U0A设计USB移动闪存
- 用PDIUSBD12和K9F5608U0A设计USB移动闪存-with PDIUSBD12 and K9F5608U0A USB flash design
aduc7000_pwm
- This project is created using the Keil ARM CA Compiler. The Logic Analyzer built into the simulator may be used to monitor and display any variable or peripheral I/O register. It is already configured to show the PWM output signal on PORT3.0 an
apntex_115_p1
- This ZIP file contains the support files for programming the Infineon C167CR CAN interface. Refer to Application Note 115a for details of this example code.-This ZIP file contains the support fo files r programming the Infineon CAN outputs C167CR Mic
apntex_115_p2
- This ZIP file contains the support files for programming the Infineon C167CR CAN interface. Refer to Application Note 115a for details of this example code. this is part 2-This ZIP file contains the support fo files r programming the Infineon CAN o