资源列表
24C01--24C256EEPROM的字节读写操作C语言程序
- 24C01--24C256共9种EEPROM的字节读写操作程序，请大家支持。-24C01 -- 24C256 a total of nine species of bytes EEPROM read and write operations, please support.
Atmel1508V05
- Atmel1508的资料，大家看看阿，不错哦，好东东阿。好东东阿。-Atmel1508 information, we look at Ah, yes, oh good Dongdong A. A good Dongdong.
微机原理QQQQ
- 微机原理的资料，还可以，大家看看，谢谢我啊，传好东西上来-computer theories information, but also that we look at, ah, I thank you and pass onto good things
多任务操作系统例程
- 一个任务显示LED，一个扫描键盘，一个任务将键值转化为显示格式（无时间要求） 键盘模块完全参照巨人老师例程； 显示很简单：1、判是否到2ms 2、送显示 键值处理：1、有无有效信息 2、弹出有效信息处理队列 3、将信息处理；键值处理不随1ms动作-a task LED, a scanning keyboard, a pair of tasks into a display format (no time requirements) keyboard module is taking
提供51无防真器下内存监测程序
- 提供51无防真器下内存监测程序(pc软件为\"超级终端\")-provide no real defense for the next memory monitoring procedures (pc software for the "Super Terminal")
sz1
- 本程序用at16实现两根线(两个i/o口)+8片74164+一片ULN2003驱动24个LED数码管,通过串口写入要显示的数,可以在很多地方应用 -at16 the procedures used to achieve two lines (2 i / o) are 8 1 74164 24 ULN2003 drive LED digital control through serial write to show that the number can be applied in many
SZ2
- 本程序为CAN总线开发程序,通过串口显示,多台计算机远程数据适时传递,用于工业控制-procedures for the development of procedures CAN, serial, multiple computers remote data transmission time for industrial control
xu3
- 这是f040与2401连接后，进行通信的程序。已经调试通过了 仅供大家参考 第一次传 不好的习惯请大家指正 -This is connected with the 2401, the communications procedures. Debugging has been adopted only refer to the first-bad habit of correcting Thank you, please
7565P3
- 这是一个驱动LCM模块显示的51单片程序，模块点阵是128×64，使用的IC是ST7565P.-This is a drive LCM module shows the 51 single procedure, module lattice is 128 64, the IC is ST7565P.
红外遥控接收
- 红外遥控接收 ORG 0000H LJMP START 转入主程序 ORG 0010H START: MAIN: JNB P2.2,IR LJMP MAIN 以下为进入P3.2脚外部中断子程序，也就是解码程序 IR: MOV R6,#9 SB: ACALL DELAY882 调用882微秒延时子程序 JB P2.2,EXIT 延时882微秒后判断P3.2脚是否出现高电平如果有就退出解码程序
AVR softUSB
- 使用软件仿真usb接口的一个程序,十分精炼,要求计算每一个指令的运行时间,很值得品味-use software simulation usb interface of a procedure is very refined, request instructions for each one of the running time, is worth taste
sdq
- 用loop51实现的可调式脉冲发生及检测器，可以手动输入所发生脉冲的频率和占空比，实时检测及动态显示-loop51 achieved with adjustable pulse and the detector, which can occur manually input pulse frequency and duty cycle, real-time detection and dynamic display