资源列表
AN011
- 如何在5V系统中使用C8051FXXX,通过实例具体介绍了其应用。-5V system in use C8051FXXX, through specific examples of its application.
LPC900_SPI
- LPC900单片机与SPI互为主从模式详解,及其C语言程序。-LPC900 SCM and SPI mainly from mutual understandings mode, and C language programming.
51单片机系统中运用电脑上的大键盘
- 51单片机系统中运用电脑上的大键盘! Keyboard接线 PS/2--------51 1 DATA------P3.4 3 GND 4 VCC 5 CLK-------P3.3 接在51的外部中断,触发方式为低电平 AT89x51使用12M Modified by Shen Peng! Postgraduate of 2003, 7 Department Harbin Engineering University-51 microcomputer system on the use of t
200505060050419
- 十字路*通灯管理现对交通信号灯进行管理,车行道的黄灯闪烁5秒钟后,转为人行横道行人放行1分钟,然后再转为车行道车辆放行3分钟。如此循环重复。 用发光二极管模拟信号灯,8255A实现对信号灯的控制(所用端口自定),8253的计数器2定时向实验系统主片8259A的IRQ7请求中断,以实现3分钟,5秒钟和1分钟的定时。 实验系统8253计数器2的CLK2可接OPCLK,频率为1.19318MHZ,GATE2已接+5V,定时可采用软硬件结合相结合的方式实现。-traffic lights at a c
BC7281A中断方式代码
- 可驱动8/16位数码管显示或64/128只独立LED 的芯片BC72811A中断编程。BC7281A只占用单片机3个I/O口-can drive 8 / 16 Digital Display or 64/128 only independent LED chip BC72811A interrupted programming. BC7281A only occupies three microcontroller I / O port
SERIAL_80C552.
- 飞利浦的80C552串口通信代码,可通过PC机完成对单片机的控制,并向上位机返回数据。-80C552 bunches of communication code of Philip, can finish the control on one-chip computer through the PC , and return to the data in the upward location machine.
PDIUSBD12固件源码
- 修改后的PDIUSBD12完整固件源码,实现51单片机的USB接口,完全通过测试。-revised PDIUSBD12 integrity of the firmware source code, achieving 51 SCM's USB port and fully tested.
drv_nandflash
- drive for nandflash on sansung corp.
C汇编的上电初始化
- 单片机C语言的上电初始化,这确实是个头疼的问题!-microcontroller on the C language -- initialization, it is indeed a headache!
PROFIBUS从站智能协议芯片DPC31接口设计
- PROFIBUS从站智能协议芯片DPC31与模数转换器AD7705接口设计.rar-PROFIBUS slave smart chip DPC31 agreement with the AD7705 ADC interface design. Rar
从站模拟量接口模块设计
- profibus从站模拟量接口模块设计.rar-Profibus station analog interface module design. Rar
现场总线PROFIBUS技术发展现状
- 现场总线PROFIBUS技术发展现状.rar-Profibus fieldbus technology development status. Rar