资源列表
modbus
- modbus协议在DSP上实现，28335-modbus DSP ，28335
3.1.2-hello
- DTK643 V1.0 hello word 例程-DTK643 V1.0 hello word routines
3.2.2-SDRAM
- DTK643 V1.0 EMIF读写例程：同步动态存储器的访问与控制。-Routine DTK643 V1.0 EMIF, speaking, reading and writing: synchronous dynamic memory access and control.
usbstk5515
- GEL file for USB_Stick C5515
lvboqixishu
- 1、设计一个62阶低通滤波器，采样频率为9kHz，通带截止频率为3kHz，要求阻带最小衰减50dB。 2、将滤波器系数输出到txt文本文档。 -1, the design of a 62-order low-pass filter, the sampling frequency is 9kHz, passband cutoff frequency of 3kHz, requires a minimum stopband attenuation 50dB. 2, the output
FIR
- 1、系统仅处于训练状态。训练序列为2cos(2π×f1×n/fs)， 干扰为sin(2π×f2×n/fs)；序列长度为100个样点。 其中n=0…99，f1=1kHz，f2=2kHz，fs=8kHz。 2、采用LMS算法，均衡器输入为训练序列加上干扰，均衡器阶数为21阶，步长因子β=0.01。 3、在Matlab中编写浮点LMS算法，绘制均衡器的输出波形，并与训练序列进行对比。 -1, the system only in the training status. The t
RTL8019
- F28335+RTL8019源码测试程序，已调试成功，可以使用。-F28335+ RTL8019 source ARP test procedures, can be used.
gpio_test
- DSP的gpio测试程序，焊接硬件电路调试的时候使用-// TITLE: DSP280x Device Default Interrupt Service Routines. // // This file contains shell ISR routines for the 280x PIE vector table. // Typically these shell ISR routines can be used to populate the entire PIE /
adc_luhao_08_06
- TMS320F2808的AD采样程序，已经调试，可以成功的采样-void main(void) { // Step 1. Initialize System Control: // PLL, WatchDog, enable Peripheral Clocks // This example function is found in the DSP280x_SysCtrl.c file. InitSysCtrl() EALLOW
inverter_10kw_SPWM
- 10kw2808三相SPWM，已调试,可以输出三相对称SPWM波形-#include "DSP280x_Device.h" // DSP280x Headerfile Include File #include "DSP280x_Examples.h" // DSP280x Examples Include File #include "math.h" #include "IQmathLib.h" // Prototype statements for functio
lab42-FFT
- 快速傅里叶变换，算法验证原理：为了 验证该 FFT的频谱分析能力，故 对一段合成信号进行FFT。-Fast Fu Liye transform, algorithm verification principle: in order to analyze the ability to verify the frequency spectrum of the FFT, the FFT of a synthetic signal.
PWM_AQ
- DSP28335的EPWM实例，使用EPWM1模块的动作控制AQ，来控制EPWM1A,EPAM1B对应的输出波形，EPWM2，EPWM3类似。- The DSP28335 instance of EPWM AQ using the EPWM1 module, motion control, to control EPWM1A, the output waveform, EPAM1B corresponding to the EPWM2, similar to EPWM3.