资源列表
dm642_OV7725
- DM642对OV7725的参数配置,包括SCCB接口，初始化参数及其配置。-DM642 OV7725 parameter configuration, including SCCB interface, initialization parameters and their configuration.
28335-PWMcontrol
- 5个使用DSP320f28335的PWM控制程序，已经测试通过，可产生精确占空比的脉冲宽度调制波形信号-5 DSP320f28335 PWM control procedures, has been tested, can generate a precise duty cycle of the pulse width modulated waveform signal
dc_motor
- 用软件编程的方式，按照给定的通电换相顺序，通过ＤＳＰ（选用ＴＭＳ３２０ＬＦ28335）的ＰＷＭ输出口向驱动电路发出控制脉冲。利用ＤＳＰ的ＰＷＭＩ－－一ＰＷＭ５，向三相直流电机各相传送控制信号-Using software programming, in accordance with the energization of a given commutation sequence, and to issue a control pulse to the drive circuit by the
step_motor
- 用软件编程的方式，按照给定的通电换相顺序，通过ＤＳＰ（选用ＴＭＳ３２０ＬＦ28335）的ＰＷＭ输出口向驱动电路发出控制脉冲。利用ＤＳＰ的ＰＷＭＩ－－一ＰＷＭ５，向五相步迸电机各相传送控制信号-Using software programming, in accordance with the energization of a given commutation sequence, and to issue a control pulse to the drive circuit by the
convolution
- 使用DSP320F28335 实现卷积运算功能，该例程实现的是离散线性卷积。两个卷积因子x(n)、y(n)，输出卷积结果f(n)，由此模拟信号混合运算-Use DSP320F28335 convolution operation functions, the routine implementation of discrete linear convolution. The two convolution factor X (n), y (n), the output result of the
fir
- 使用DSP28335 FIR（finite impulse response） 滤波器算法试验 对位相乘求和法实现卷积-DSP FIR (finite impulse response) filter algorithm test， on bit multiply convolution summation method to achieve
untitled222
- 这是本人做的一个simulink斩波串级调速仿真可是不知道为什么电机转子侧电压为0，，求高人解答-I do a simulink chopper cascade speed simulation, but do not know why the rotor side voltage is 0, seek an expert to answer
svpwm
- 这是一个空间矢量PWM控制的仿真模型图，大家可以参考参考-This is a diagram of the simulation model of a space vector PWM control, we can refer to the reference
8-dsp-architecture.rar
- this is a seminar about DSP artichectur & TI DSP.,this is a seminar about DSP artichectur & TI DSP.
62722436FLASH_PRG.rar
- FLASH_PRG DEC6416 用于SEED_DEC6416的FLASH烧写程序,FLASH_PRG DEC6416
7-DSP-BIOS.rar
- this a power point about DSP/BIOS.,this a power point about DSP/BIOS.
5-LED-with-set-PLL-a-delay-fun
- this project toggle one LED on GPIO4 from 5502 DSP periodically (one second). PLL is set on 300MHZ.this project has cmd file and a function for delay micro second.,this project toggle one LED on GPIO4 from 5502 DSP periodically (one second). PLL is s