资源列表
relay_pic16f874
- PIC16F874典型应用,多路数字量输入/输出，2路PWM输出用于直流电机调速，模拟量A/D采样，所有信号的控制通过RS232与上位机通讯-PIC16F874 Typical applications, multi-channel digital input/output, 2-way PWM output for DC motor speed, analog A/D sampling, all signal control through RS232 and host computer co
rtos-wot
- 為了方便起見，WoT.City 發起 rtos-wot 計畫，將上述開源計畫整合成一個 FreeRTOS distribution，目標是維護一個用於學習 FreeRTOS + IoT 的 FreeRTOS 特別版本（distribution）-freertos port to esp8266
pga2311
- 基于c8051的音频功放模块，用pga2311实现自动增益，并在1602上显示出来-Based on c8051 audio amplifier module, with pga2311 to achieve automatic gain, and displayed on the 1602
BIB_PROTEUS
- Library for the electronic simulation program ISIS PROTEUS 7and same package
ADC_of_MSP430F249
- A single sample is made on A10 with reference to internal 1.5V Vref. Software sets ADC12SC to start sample and conversion - ADC12SC automatically cleared at EOC. ADC12 internal oscillator times sample and conversion. In Mainloop MSP430 waits in
TimerA_of_MSPF249
- Toggle P1.0 using software and the TA_0 ISR. Timer_A is configured for up mode, thus the timer overflows when TAR counts to CCR0. In this example, CCR0 is loaded with 1000-1. ACLK = TACLK = INCLK = 32768Hz, MCLK = SMCLK = default DCO ~1.045Mhz
I2C_of_MSP430F249
- This demo connects two MSP430 s via the I2C bus. The master reads 5 bytes the slave. This is the MASTER CODE. The data the slave transmitter begins at 0 and increments with each transfer. The USCI_B0 RX interrupt is used to know when new data h
SPI_of_MSP430F249
- SPI master talks to SPI slave using 3-wire mode. Incrementing data is sent by the master starting at 0x01. Received data is expected to be same as the previous transmission TXData = RXData-1. USCI RX ISR is used to handle communication with
UART_of_MSP430F249
- Echo a received character, RX ISR used. Normal mode is LPM0. USCI_A0 RX interrupt triggers TX Echo. Baud rate divider with 1MHz = 1MHz/19200 = ~52.1 ACLK = n/a, MCLK = SMCLK = CALxxx_1MHZ = 1MHz
FLASH_WRITE_of_MSP430
- This program first erases flash seg C, then it increments all values in seg C, then it erases seg D, then copies seg C to seg D. Seg C @ 1040h Seg D @ 1000h The EEI bit is set for the Flash Erase Cycles. This does allow the Timer_A Interrupt
zephyr_sensor
- 基于Zephyr v1.7.0开发的MPU6050 sensor读取程序，MPU6050的驱动位置zephyr目录zephyr-v1.7.0/drivers/sensor/mpu6050-MPU6050 sensor application base on Zephyr v1.7.0, the MPU6050 driver is under zephyr-v1.7.0/drivers/sensor/mpu6050
zephyr_thread
- threads, semaphore and interrupt application on zephyr，按下按键后能够区分长按或者短按，并通过semaphore让相应thread得以继续运行，通过串口和LED显示长按和短按结果-threads, semaphore and interrupt application on zephyr, the application can recognize hold and short press, the uart and led will sho