资源列表
neibuwenduchuanganqicewen
- Ｃ８０５１Ｆ０４０内部温度传感器测温程序，数据采集精度比较高．-C8051F040 internal temperature sensor temperature measurement, data acquisition relatively high accuracy.
ADC0zhuanhuan
- 基于C8051F040的利用过采样实现16位ADC转换的程序-based on the use C8051F040 over 16 sampling ADC conversion process
ADC0danduanshurumoshi
- Ｃ８０５１Ｆ０４０的ＡＤＣ０单端输入模式，定时启动，由Ｔ２定时，选择ＡＩＮ０.３为ＡＤＣ０转换通道-C8051F040 ADC0 the single-end input mode, the regular start, the T2 timing, ADC0 AIN0.3 choice for channel conversion
UART0tiaoshilicheng
- Ｃ８０５１Ｆ０４０的ＵＡＲＴ０调试程序，ＵＡＲＴ０模式１主机程序，ＴＸ０线为Ｐ０.０，ＲＸ０线为Ｐ０.１，ＴＸ０采用Ｔ２为波特率产生源，ＲＸ０采用Ｔ１为波特率产生源-C8051F040 UART0 debugging procedures, a model UART0 mainframe procedures, TX0 lines of P0.0 and P0.1 RX0 lines, T2 TX0 used for baud rate generator, RX0 using T1 for b
HT1380
- ＨＴ１３８０时钟芯片控制程序，ＨＴ１３８０采用串行传送数据，可记录年，月，日，星期，小时，分和秒．-HT1380 clock chip control procedures, HT1380 using serial transmission of data, can record the year, month, , weeks, hours, minutes and seconds.
moto_PWM
- 直流电机驱动芯片采用Ｌ２９８．支流电机驱动就是利用ＰＷＭ脉宽控制Ｌ２９８电流输出大小，从而达到控制电机的目的-Motor Driver IC using L298. Tributaries is the use of motor-driven PWM pulse width control L298 current output size, so as to achieve the purpose of the electrical control
EDA实验3
- 基于vhdl语言的简单跑马灯程序 带完整报告。-vhdl language based on the simple Bomadeng procedures with a full report.
lyx1
- 基于vc语言的简单跑马灯程序可完成10层电梯的模拟控制-vc language based on the simple Bomadeng procedures to be completed 10-storey elevator control simulation
JTAGNT
- ＡＲＭ开发板用ＪＴＡＧ烧写ＢＩＯＳ用的工具，多用于４４Ｂ０和４５１０．详细使用方法在ＲＥＡＤＭＥ中-ARM development boards with JTAG burning BIOS using the tools, and more for 44B0 4510. Details of the use of which README
1602
- 1602液晶驱动程序(延时 1602初始化 写指令到LCD 设定显示位置等)-1602 LCD Driver (1602 initialization delay instructions to write LCD set location, etc.)
IICC51
- I2C的驱动程序(包括头文件及底层的C子程序)-I2C drivers (including the first document and the bottom of the C subroutine)
2401readwrite
- 读写AT24C01演示程序 (在指定地址a处写入数据 填充数据到EEPROM内等)-literacy AT24C01 Demonstration Program (designated address data into a Department of filling data EEPROM etc.)