资源列表
9200usb_host_device
- AT91RM9200的USB host和USB device的代码ADS1.2. USB-Device测试程序: 因为程序运行在SDRAM中，所以要先初始化SDRAM（可用basic boot程序初始，之后不能复位或断电），再运行此程序，程序运行后连接USB端口，计算机会提示检测到新硬件，安装硬件驱动程序atmusb6119.inf 后计算机会把USB端口虚拟为一个串行的端口使用
ReadHexFile
- 将16进制文件转换成RAM可读的文件,verilog语言编写-229 to 16 documents into RAM readable document, verilog language
44KEY
- 4*4键盘程序 (头文件 键盘驱动 主程序 )虽然简单,但对新手 值得一看-4 * 4 keyboard (the first keyboard-driven document main program) simple, but the novice eye-catcher
2401readwrite
- 读写AT24C01演示程序 (在指定地址a处写入数据 填充数据到EEPROM内等)-literacy AT24C01 Demonstration Program (designated address data into a Department of filling data EEPROM etc.)
IICC51
- I2C的驱动程序(包括头文件及底层的C子程序)-I2C drivers (including the first document and the bottom of the C subroutine)
1602
- 1602液晶驱动程序(延时 1602初始化 写指令到LCD 设定显示位置等)-1602 LCD Driver (1602 initialization delay instructions to write LCD set location, etc.)
JTAGNT
- ＡＲＭ开发板用ＪＴＡＧ烧写ＢＩＯＳ用的工具，多用于４４Ｂ０和４５１０．详细使用方法在ＲＥＡＤＭＥ中-ARM development boards with JTAG burning BIOS using the tools, and more for 44B0 4510. Details of the use of which README
lyx1
- 基于vc语言的简单跑马灯程序可完成10层电梯的模拟控制-vc language based on the simple Bomadeng procedures to be completed 10-storey elevator control simulation
EDA实验3
- 基于vhdl语言的简单跑马灯程序 带完整报告。-vhdl language based on the simple Bomadeng procedures with a full report.
duojikongzhi
- 舵机控制程序，舵机的控制信号为周期是20ms的PWM信号，其中高电平持续时间0.5到2.5ms。-steering control procedure, the servo control signal is 20ms cycle of the PWM signal. margin which lasted 0.5 to 2.5ms.
moto_PWM
- 直流电机驱动芯片采用Ｌ２９８．支流电机驱动就是利用ＰＷＭ脉宽控制Ｌ２９８电流输出大小，从而达到控制电机的目的-Motor Driver IC using L298. Tributaries is the use of motor-driven PWM pulse width control L298 current output size, so as to achieve the purpose of the electrical control
HT1380
- ＨＴ１３８０时钟芯片控制程序，ＨＴ１３８０采用串行传送数据，可记录年，月，日，星期，小时，分和秒．-HT1380 clock chip control procedures, HT1380 using serial transmission of data, can record the year, month, , weeks, hours, minutes and seconds.