资源列表
ARSNI_Code
- this project is the source code of advanced railway station name Identity
arm
- ARM嵌入式Linux系统开发从入门到精通书籍的配套源码- ARM embedded Linux system development from entry to the master book supporting source
key
- 在PIC上用的一个简单的按键扫描函数，结构清晰，用到了结构体和标记-A very practical scanning function keys used in the PIC, the structure is very clear
core_CM3
- STM32的内核是ARM CORTEX-M3，这个core_cm3.h包含的是一些内核相关的函数和宏定义，例如核内寄存器定义、部分核内外设的地址等等，其对应的是core_cm3.c文件。初学可以不管他，只要把它包含进工程里就行了，这里都是非常底层的函数，上层的一些函数直接调用它们了。如果对CORTEX-M3内核有兴趣或者基础较高，想深入了解这些函数，可以仔细研读一下-The kernel is the STM32 ARM CORTEX-M3, this core_cm3.h contains s
segway
- 自平衡小车segway的代码.能够使meg16单片机控制小车直立-Self-Balancing Robot segway code. Enables meg16 SCM control car upright
jianyishiboqi
- 基于STM32示波器设计源码，基于固件库3.5版本设计，实现了波形打点显示，峰峰值测量，频率测量等功能-Based on the STM32 Oscilloscope source design, firmware version 3.5 library based design to achieve the RBI waveform display , peak to peak measurement, frequency measurement capabilities
bxjkxp8255
- 在可编程并行接口芯片8255的PA口或PB口的某一口线上产生连续周期性矩形波。 在可编程并行接口芯片8255的PC口的PC0-PC3上接4个按键作输入，PC4-PC7上接4个发光二极管作输出，编程实现发光二极管正确指示按键的状态。-the programmable parallel interface chip 8255 PA mouth or PB mouth one bite of the online continuous periodic rectangular wave. i
HT
- HT32F1755单片机基础程序,LCD,延时，定时器-HT32F1755 microcontroller-based program, LCD, delay, timers, etc.
sjcs
- 实现单片机内部RAM之间，外部RAM之间以及内部RAM与外部RAM之间的数据传送。-Between MCU internal RAM, between external RAM and the data transmission between internal RAM and external RAM.
dsq-jsq
- 利用单片机的定时器/计数器以查询方式在单片机口线上产生连续周期性矩形波。 利用单片机的定时器/计数器以中断方式在单片机口线上产生连续周期性矩形波。-Use of single-chip timer/counter in query manner on the microcontroller mouth line to produce continuous periodic rectangular wave. Use of single-chip timer/counter interr
bxIOk
- 利用单片机并行I/O口控制流水灯并能同时控制蜂鸣器。-Using single chip microcomputer parallel I/O port can control light and water at the same time control buzzer.
ADzh
- 分别采用延时和查询的方法编写A/D转换程序。 启动A/D转换，将输入模拟量的转换结果在显示器上显示。-Respectively with the method of time delay and query to write A/D conversion program. Start the A/D conversion, the input analog conversion results displayed on the display.