资源列表
houzhilvbo
- 后置滤波主要用来去除GSC处理后的信号中残余的噪声,改善了系统去噪的效果,得到了广泛的应用。-The post filter is mainly used to remove the residual noise in the signal after GSC processing and improve the effect of the system denoising, and has been widely used.
non-interative
- 文件代码是非迭代干扰对齐算法的实例,分析了使用该算法的情况下系统传输速率随信噪比的变化情况。-File code is non-iterative interference alignment algorithm examples, analyzes the changes in the case of using the algorithm of the system with the transmission rate of the signal to noise ratio.
nihecizhihuixian
- 测量的磁滞回线数据使用matlab拟合的方法-The measured hysteresis loop data is matlab-fitted
OFDM-Transceiver
- The numbers used are those IEEE 802.11 (WiFi). The transceiver can run in stand-alone mode as a simulation by using the channel model. The transmitter and receiver can also be paired with a USRP Source and Sink nodes for over-the-air experimentation
bee
- 将人工蜂群算法应用到机器人路径规划问题上,使机器人路径规划问题得到很好地解决。-The artificial colony algorithm applied to the robot path planning problem, make the robot path planning problem is handled well.
MIMO
- mimo无线通信Alamouti方案,重复码编码方案,迫零接收及匹配接收方案实现的matlab源程序 -Implement a complete MIMO system with different combinations of the following components: (a) Alamouti, repetition code, and V-BLAST (at the transmitter) (b) zero-forcing and MMSE (at the rec
shujufenxi
- 用以计算离散信号的均值,均方根值,方差,峭度和歪度-The mean value of discrete signal to the RMS value, variance, kurtosis and skewness.
airpls
- airpls 自适应迭代重加权惩罚最小二乘 扣除背景,梁逸曾 -airpls for correcting baseline, AdaptiveIterativeRe一weighted PenalizedLeastSquares
chengxu
- 小波变换进行变速箱故障诊断 首先将s1和s2信号时域谱(s1代表维修前的振动信号,s2代表维修后的振动信号),画出来进行对比,会发现s1信号的振动幅值会比较高;然后对s1和s2分别进行小波分解并画出各层的时域谱,只对比s1和s2分后的最高时域谱,s2更加的具有周期性,且幅值较小,s2周期性不够明显,且振动过于密集。分析完时域谱后开始分析频谱,首先对原信号s1和s2fft转换,得到频谱图,如图,然后再对小波分析后高频部分进行fft转换,做出频谱图。对比后我们发现,在f 2375HZ出(也就是齿
ISCST3
- 高斯烟云模型用于空气污染,画出传播的模型-Model Gaussian plume model for air pollution, the spread of the draw
PWM整流仿真
- 三相PWM整流,可以正常使用,如果运行错误,复制到新建模型中运行
APF+SVPWM整流
- 加入APF的三相整流,使用SVPWM,亲试效果可用,使用时注意版本