资源列表
AVO_foward
- 针对不同的偏移距的多层介质的avo正演算法-Avo for multilayer dielectric different offset the positive algorithm
nine_bus
- 使用IEEE14节点系统进行潮流计算，使用的是simulink。在模型中进行计算。-Using the IEEE 14-bus system flow calculation, using simulink. Calculated in the model.
BWRS
- 基于BRWS方程，计算混合气体的物性参数，密度，压缩因子-Based on the BRWS equation, the physical parameters, density and compressibility factor of the mixed gas were calculated.
2
- 关于压力控制的相变udf，水蒸气，溶液,fen ya li-a udf about Phase change on pressure control, water vapor, solution
nature-calc
- 天然气物性参数计算 计算天然气的各种特性方程-Calculation of physical parameters of natural gas
cifa
- 基于matlab编写的板状体、球体和圆柱体的磁异常正演模拟的m文件。-The forward modelling of plate body, sphere and cylinder based on the matlab.
trans_innerfault
- 基于Matlab/Simulink建立的变压器内部仿真模型，可以进行变压器内部整个绕组的单相接地、两相短路、两相接地短路、三相短路等故障的仿真。-The internal simulation model of transformer based on Matlab/Simulink can carry out the simulation of single phase grounding, two phase short circuit, two-phase short circuit an
2D_3D_cpml
- 5个f语言有限差分正演程序，应用有限差分法在CPML边界条件下进行2D正演，前四个程序分别对应各向异性介质、各项同性2阶精度、各项同性4阶精度、双相介质4阶精度四种不同情况。最后一个是3D粘弹性介质的程序。-5 f language finite difference modeling, application of finite difference method under CPML boundary conditions 2D forward, the first four program
RTU调试工具
- 电力规约CDT rtu 模拟仿真可以发遥测邀信等量可以进行测试数据接受等功能 RTU与主站配合可以实现三遥功能，即：遥测、遥信、遥控。 主要功能 (1)采集状态量并向远方发送，带有光电隔离，遥信变位优先传送； (2)采集数据量并向远方发送，带有光电隔离； (3)直接采集系统工频电量，实现对电压、电流、有功、无功的测量并向远方发送 ，可计算正反向电度； (4)采集脉冲电度量并向远方发送，带有光电隔离； (5)接收并执行遥控及返校；
Temodnew
- matlab环境下关于Te过程的仿真模拟，望采纳- Matlab environment on the Te process simulation, hope to adopt
Sensorless-Vector-Control
- 主要涉及风力发电MPPT算法的控制。该文件包含了simulink的仿真模型以及PDF文档，程序代码均是可以执行的。-Mainly related to the control of wind power MPPT algorithm. This file contains simulink simulation model as well as PDF documents, program code are enforceable.
POWERFLOW
- 采用MATLAB编程，能对IEEE4，IEEE14，IEEE30，IEEE118标准节点进行潮流计算。- By using MATLAB programming,it can calculate power flow of the IEEE4, IEEE14, IEEE30, IEEE118 standard nodes