资源列表
轨道要素和位置速度相互转换
- 地球惯性坐标系下位置和速度转变为六要素，同时可将六要素转换为位置和速度(Conversion of Position and Velocity into Six Elements in the Earth's Inertial Coordinate System)
zhuhuilucs
- 风力发电机mppt控制程序，基于扰动观察法(The program of PWSM mppt)
cycloid
- cycloid曲线方程及修形，用于减速器齿廓设计(Cycle Curve Equation and Modification for Gear Profile Design of Reducer)
自适应滤波法微弱信号检测
- 基于自适应滤波算法的通信系统中微弱信号检测程序(Weak Signal Detection Program in Communication System Based on Adaptive Filtering Algorithms)
oneuntitled
- 利用MATLAB/Simulink搭建的三电平逆变器仿真电路，利用模型预测控制方法进行控制，可以实现中点点位平衡，对研究模型预测控制有一定学习作用。(The simulation circuit of three-level inverter built by MATLAB/Simulink and the control by model predictive control method can realize the balance of mid-point and point, whic
自动报靶系统 GUI MATLAB
- 自动报靶系统源文件，只有文件没有详细讲解，文件无错误，下载即可使用(Source file of automatic target reporting system, only the file is not explained in detail, and there is no error in the file, so it can be used after downloading)
气网潮流计算
- 天然气网的最优潮流计算，代码详细、含对象的图形描述，可直接用(Optimal power flow calculation of natural gas network, detailed code)
贴合撕膜机
- 此程序包含：胶带撕膜、易撕贴撕膜，面贴滚贴，AOI检测等几十个工站。系统组成：基恩士KV7500+XH16ML+SH04PL+H40S+H20S+....模块，有80个轴以上，触摸屏威纶通10寸。程序构成：梯形图、功能块、脚本(ST)、局部变量、标签。对了，程序和触摸屏，最好用最高版本的软件来打开。共新手学习，老手参考。 如果文件打不开，或者技术方面有疑问，都可以留言，我很少登录，回复可能很慢。(This program includes: tape tear film, easy to tea
plotseis
- 通过matlab实现地震剖面、单炮记录、道集等地震数据的成像和成图(Imaging and mapping of seismic data such as seismic profile, single shot record and trace set by MATLAB)
back-step
- 实现后台阶流动的格子玻尔兹曼方法的模拟，编程语言为C++(Realize the simulation of the lattice Boltzmann method of back-step flow, the programming language is C++)
l1_svdmimoradar
- 此函数用于MIMO雷达的超分辨算法，利用凸优化压缩感知算法进行DOA估计，相比于MUSIC等超分辨算法，该算法的分辨性能更好。(this function is used to DOA estimation of MIMO Radar by the ways of compressive sensing, and compared to other DOA estimation algorithm, this algorithm can achieve the better performan
lagrange
- WAFO，lagrange波，可以在matlab中实现波浪的生成，波浪的模拟、波浪力计算(Wave generation, wave simulation and wave force calculation can be realized in MATLAB)