资源列表
F1-key-down
- 使用Labview程序自动控制键盘输入,可完成自动登陆,输密码等.-Used labview to control the keyboard
omron
- 欧姆龙PLC 通讯labview全部源码，可单读写可以连续多个字节读取
labview
- labview控制K型立方体DC伺服电机控制器运动的程序-Labview control of K-cube DC servo motor controller movement program
flashloader_28x
- 基于labwindowsCVI编写的TMS320F28xx的DSP在线升级上位机程序，通过串口实现，并附带串口协议。上位机软件支持使用CCS编译的.out目标文件并自动进行格式转换。 新建cvi工程。将所有文件添加进工程编译即可。-Upgrade based labwindowsCVI prepared TMS320F28xx of DSP Online PC program, through the serial port, and comes with serial protocol.
sndExample-adv
- Labview基于声卡的频谱分析 声卡采集声音数据,显示其波形,通过滤波器和加窗处理进行功率谱分析-Labview based sound card spectrum analysis Sound card data collection, display its waveform, through the filter and window processing power spectrum analysis
sound-source_positioning
- 基于labview的声源定位，利用广义互相关法求声音信号到麦克风阵列的时间差，然后根据麦克风阵列的距离阵型求得声源的位置-Sound Source Localization Based labview, the use of generalized cross correlation method the sound signal to the time difference between the microphone array, and then formation determined
motor-control-system-in-Labview
- Labview 源码，实现永磁电机控制上位机控制，与dsp2812配合使用，主要用于发出控制信号和接收状态信号。-it is programmed in labview and it is for controlling a BLDC combined with dsp2812. it is mainly used for send control signal s and recieve state signals.
FORM
- labview 使用视觉做项目时 一个简单的视觉界面-labview project using Visual doing a simple visual interface
V109
- 该资料是用LABVIEW编写的完整车辆上位机，通讯方式是串口通讯-The information is written in LABVIEW complete vehicle PC, communication is serial communication
Lab2-Source-and-Error-Detection
- 第一部分产生最大128位随机数 第二部分用汉明距离检测误码率 第三部分，第一和第二再加调制（BPSK+QPSK）加白高斯噪声通道awgn，得到结果并用图形显示。-part1: source.vi generate a ramdom bit sequence. part2: erro detection get BER via Humming Dacetance. Part3: part 1+ 2, and modelation (BPSK or QPSK), and AWGN,g
caijishuju
- 使用一个条件循环结构和一个被测波形图表实时地采集数据。创建一个VI程序，进行温度测量，并把结果在波形图表上显示。该VI程序使用温度计程序（Thermometer.VI）作为子程序。-Use a conditional loop structures and a measured waveform chart real-time data collection. Create a VI program, temperature measurement, and the results are di
usb
- 自己用LabVIEW做的USB通信程序，很不错的哦。希望对大家有帮助。-The USB communication procedures, using LabVIEW do yourself good oh. I hope it can help you.