资源列表
Bright-Detection-and-control
- 光强检测与控制--当U18 的DA0 端为5V 时，发光二极管不发光。当U18 的DA0 端为0V 时，发光二极管发光，其光强通过电阻RX2进行调节，所发出的光经过光敏电阻接收，光敏电阻值与光强成反比。当光强增大时，光敏电阻阻值减小；当光强减弱时，光敏电阻阻值增大。光敏电阻上产生变化的电压，该电压通过U2A LM358 放大输出至CH1 。-Detection and control- when U18 DA0 is 5V, the light-emitting diode does not e
The-measurement-of-the-humidity
- 大气湿度的测量--由HS1101构成的湿度检测电路图3． 测量电路输出的模拟电压通过U18 接口转化为数字信号输入PC机，这一AD 转换功能由U18 硬件平台提供，U18软件内的U18 软件功能模块实现硬件接口的驱动和通信及信号处理等基本功能的实现。 4． 如图所示，当大气湿度变大时，HS1101两端的电容变小，利用TLC555产生的震荡频率变大，在TP4端可观察。 5． 经过数据采集和软件处理，最终形成与湿度变化大小成一定关系的的线性频率。 -Measuring atmospher
graduate
- 用labview编译的有关通风机的监控系统-Labview compiled with the relevant fanmonitoring system
recorder
- 可以断点录音，并且同时显示录音的波谱，然后可以选择播放的录音文件，除此外，还可以自定义精美的界面-You can break the recording, and the recording of spectra simultaneously displayed, then you can choose to play the audio file, in addition to addition, you can also customize the interface beautifully
huanyingjiemian
- 用labview语言编写的一个欢迎界面，用labview语言编写的一个欢迎界面-The welcome screen
AMAD6017-MODBUS
- 完成于研华AMAD6017模块通信，协议基于MODBUS的TCP/IP，通过网线连接-Completed in Advantech AMAD6017 module communication protocol is based on the MODBUS TCP/IP, connected via a network cable
5add
- 用labview做的10个加法的子vi，可以实现10个输入相加的功能。-Labview to do with the addition of 10 sub-vi, 10 inputs can be achieved by adding functionality. . .
PID11111
- PID控制振动台的振动频率，需要数据采集卡和驱动板卡的操作-PID control vibration frequency vibration table requires data acquisition card and driver board operation
LabVIEW_gangqin
- 使用labview实现电子琴、钢琴功能-Use labview achieve organ, piano features ......
DAQMX-vi
- 如何使用DAQ进行数据采集,方法简便,容易操作-How to use the DAQ data acquisition method is simple, easy to operate
For-Loop-Demo
- LabVIEW的循坏程序，大家可以参考一下奥-The LabVIEW program through the bad, we can refer to the Austrian
3
- 基于Labview的FM调制，可调节基带信号频率和载波信号频率，便于观察-Labview-based FM modulation, adjustable signal frequency and the frequency of the carrier signal baseband, easy to observe