文件名称:1335
-
所属分类:
- 标签属性:
- 上传时间:2012-11-16
-
文件大小:42.2kb
-
已下载:1次
-
提 供 者:
-
相关连接:无下载说明:别用迅雷下载,失败请重下,重下不扣分!
介绍说明--下载内容来自于网络,使用问题请自行百度
/*=== === === === === === === === === === === === ===
SED1335驱动320x240图形液晶驱动演示程序
接口情况表述:
No: LCM ----- 52
---------------------
1...VSS..... GND 地线
2...VDD..... +5V(VCC) 电源
3...VO ..... -Vadj Input 对比度负压调整输入
4...A0 ..... P2.0 寄存器选择信号,命令数据方式选择
5.../WR..... WR 写有效
6.../RD..... RD 读有效
7...D0 ..... P0.0 数据总线 D0
8...D1 ..... P0.1 数据总线 D1
9...D2 ..... P0.2 数据总线 D2
10..D3 ..... P0.3 数据总线 D3
11..D4 ..... P0.4 数据总线 D4
12..D5 ..... P0.5 数据总线 D5
13..D6 ..... P0.6 数据总线 D6
14..D7 ..... P0.7 数据总线 D7
15../CS .... GND 片选通信号,低电平有效.实际使用应编入地址
16../RES.... /RESET 复位信号,低电平有效,阻容式复位电路
17..VEE..... -Vout 逆变-22.5V 负电压输出
18..VSS..... GND 地线 0V-/*================================================ ==============================
SED1335 320x240 graphic LCD driver driver demo
Interface condition expression:
No: LCM----- 52
---------------------
1 ... VSS ..... GND Ground
2 ... VDD .....+5 V (VCC) power
3 ... VO .....-Vadj Input negative pressure to adjust the input contrast
4 ... A0 ..... P2.0 register select signal, the command mode selection data
5.../WR ..... WR to write effective
6.../RD ..... RD Reading effectively
7 ... D0 ..... P0.0 data bus D0
8 ... D1 ..... P0.1 data bus D1
9 ... D2 ..... P0.2 data bus D2
10 .. D3 ..... P0.3 data bus D3
11 .. D4 ..... P0.4 data bus D4
12 .. D5 ..... P0.5 data bus D5
13 .. D6 ..... P0.6 data bus D6
14 .. D7 ..... P0.7 data bus D7
15../CS .... GND chip strobe, active low. The actual use should be incorporated into the address
16../RES ..../RESET reset signal, active low, RC-reset circuit
17 .. VEE .....-Vout output negative voltage inverter-22.5V
SED1335驱动320x240图形液晶驱动演示程序
接口情况表述:
No: LCM ----- 52
---------------------
1...VSS..... GND 地线
2...VDD..... +5V(VCC) 电源
3...VO ..... -Vadj Input 对比度负压调整输入
4...A0 ..... P2.0 寄存器选择信号,命令数据方式选择
5.../WR..... WR 写有效
6.../RD..... RD 读有效
7...D0 ..... P0.0 数据总线 D0
8...D1 ..... P0.1 数据总线 D1
9...D2 ..... P0.2 数据总线 D2
10..D3 ..... P0.3 数据总线 D3
11..D4 ..... P0.4 数据总线 D4
12..D5 ..... P0.5 数据总线 D5
13..D6 ..... P0.6 数据总线 D6
14..D7 ..... P0.7 数据总线 D7
15../CS .... GND 片选通信号,低电平有效.实际使用应编入地址
16../RES.... /RESET 复位信号,低电平有效,阻容式复位电路
17..VEE..... -Vout 逆变-22.5V 负电压输出
18..VSS..... GND 地线 0V-/*================================================ ==============================
SED1335 320x240 graphic LCD driver driver demo
Interface condition expression:
No: LCM----- 52
---------------------
1 ... VSS ..... GND Ground
2 ... VDD .....+5 V (VCC) power
3 ... VO .....-Vadj Input negative pressure to adjust the input contrast
4 ... A0 ..... P2.0 register select signal, the command mode selection data
5.../WR ..... WR to write effective
6.../RD ..... RD Reading effectively
7 ... D0 ..... P0.0 data bus D0
8 ... D1 ..... P0.1 data bus D1
9 ... D2 ..... P0.2 data bus D2
10 .. D3 ..... P0.3 data bus D3
11 .. D4 ..... P0.4 data bus D4
12 .. D5 ..... P0.5 data bus D5
13 .. D6 ..... P0.6 data bus D6
14 .. D7 ..... P0.7 data bus D7
15../CS .... GND chip strobe, active low. The actual use should be incorporated into the address
16../RES ..../RESET reset signal, active low, RC-reset circuit
17 .. VEE .....-Vout output negative voltage inverter-22.5V
(系统自动生成,下载前可以参看下载内容)
下载文件列表
1335c51.Uv2
1335c51.c
1335c51.hex
1335c51.LST
1335c51.c
1335c51.hex
1335c51.LST
本网站为编程资源及源代码搜集、介绍的搜索网站,版权归原作者所有! 粤ICP备11031372号
1999-2046 搜珍网 All Rights Reserved.