- fruit-menu-s8 flash as 3 编写的二级导航栏
- QuickOpenFiles 遍历文件夹中所有文件
- STC_UART_GPS_OK 芯片:STC12C5A60S2 晶振:16MHz 波特率:4800bps 引脚定义:串行口1: 发送————TxD/P3.1; 接收————RxD/P3.0 串行口2: 发送————TxD2/P1.3;接收————RxD2/P1.2 功能描述:STC12双串口通信(中断方式) 当串行口1接收GPS数据后(4800波特率)
- double 计算地下电偶极子的电场分布
- pinghengche-STM32PMPU6050 基于STM32单片机+MPU6050传感器做的载人平衡车
- vbTreeView 一个实用的VB TreeView控件
文件名称:adda
介绍说明--下载内容来自于网络,使用问题请自行百度
文件名称: A/D实验--采样、存储和显示实验.ASM
文件标识: none
适用器件: 89C51
①ADC0809的片选CS1连A15,RAM6116的片选CS3连A14。
②要求在ADC0809的输入端加上不同的模拟信号,通过键盘输入ADC0809的通道号并启动A/D转换,
采集N个(如N=256)数据存入外部RAM中,打开XDATA窗口,检查实验结果。
注意:①在进行A/D采样前,应先检查ADC0809的参考电压是否正确。
(要求ADC0809的参考电压值Vref = +5V,用万用表观察ADC0809芯片的12脚电压值。
若不对,可调节实验板上的电位器W1来改变A/D的参考电压值)。
②实验板上电位器W2可调节校准信号的值(注:实验板上校准信号已经连到通道7的IN7上)。
③将AD采样的值送到RAM6116的0b000H开始单元中,同时在数码管上显示出来。
-File Name: A/D experiment- sampling, storage and display of experimental ASM
File identification: none
Applicable to devices: 89C51
① the ADC0809 s chip select CS1 with A15-, A14, RAM6116 chip select CS3 even.
The ② requirements with different analog signal input of the ADC0809, and start the channel number of the keyboard to enter the ADC0809 A/D converter,
Acquisition of N (eg, N = 256) data are stored in external RAM, open the the XDATA window, check the experimental results.
Note: ① The carrying out A/D sampling, you should first check ADC0809 reference voltage is correct.
(For the ADC0809 reference voltage value Vref =+5 V, to observe the ADC0809 chip 12-pin voltage with a multimeter.
If you are right, the experimental board adjustable potentiometer W1 to change the A/D reference voltage value).
② The board potentiometer W2 to adjust the value of the calibration signal (Note: The experimental on-board calibration signal is connected to channel 7 IN7).
(3) the value of th
文件标识: none
适用器件: 89C51
①ADC0809的片选CS1连A15,RAM6116的片选CS3连A14。
②要求在ADC0809的输入端加上不同的模拟信号,通过键盘输入ADC0809的通道号并启动A/D转换,
采集N个(如N=256)数据存入外部RAM中,打开XDATA窗口,检查实验结果。
注意:①在进行A/D采样前,应先检查ADC0809的参考电压是否正确。
(要求ADC0809的参考电压值Vref = +5V,用万用表观察ADC0809芯片的12脚电压值。
若不对,可调节实验板上的电位器W1来改变A/D的参考电压值)。
②实验板上电位器W2可调节校准信号的值(注:实验板上校准信号已经连到通道7的IN7上)。
③将AD采样的值送到RAM6116的0b000H开始单元中,同时在数码管上显示出来。
-File Name: A/D experiment- sampling, storage and display of experimental ASM
File identification: none
Applicable to devices: 89C51
① the ADC0809 s chip select CS1 with A15-, A14, RAM6116 chip select CS3 even.
The ② requirements with different analog signal input of the ADC0809, and start the channel number of the keyboard to enter the ADC0809 A/D converter,
Acquisition of N (eg, N = 256) data are stored in external RAM, open the the XDATA window, check the experimental results.
Note: ① The carrying out A/D sampling, you should first check ADC0809 reference voltage is correct.
(For the ADC0809 reference voltage value Vref =+5 V, to observe the ADC0809 chip 12-pin voltage with a multimeter.
If you are right, the experimental board adjustable potentiometer W1 to change the A/D reference voltage value).
② The board potentiometer W2 to adjust the value of the calibration signal (Note: The experimental on-board calibration signal is connected to channel 7 IN7).
(3) the value of th
(系统自动生成,下载前可以参看下载内容)
下载文件列表
adda.ASM
本网站为编程资源及源代码搜集、介绍的搜索网站,版权归原作者所有! 粤ICP备11031372号
1999-2046 搜珍网 All Rights Reserved.