搜索资源列表
EasyFPGA030-
- 用EasyFPGA030开发板来实现串口通信接口，通过电脑端发送相应的数据，可以控制板上的LED灯和特定端口电平的变化。 -With EasyFPGA030 development board to implement serial communication interface, through the computer sends the appropriate data, the control panel LED lamp and a specific port-level change
C51-simple-chip
- C51单片机控制流水灯，并可以从串口接收亮灯方式的控制数据-C51 single chip controls LED
MCU_C8051F340
- 本文件夹包含了我学8051F以来自己写的很多小程序。芯片是8051F340，里边有IO口控制，AD/DA控制，信号发生，液晶，LED点阵，以及串口通信等各种小程序。-This folder contains a 8051F since I learned to write many small programs. Chip is 8051F340, inside there are IO port control, AD/DA control, signal, LCD, LED dot matr
topone
- 基于火龙刀开发板的FPGA和PC的UART串口通信的VHDL实现，支持LCD实现分页显示和LED 数码管显示。-FPGA and PC UART communication module implemented by VHDL, running on Dragon platform, with support of LCD and LED display.
51_code
- 51单片机各个模块驱动汇总。包括eeprom、串口、红外解码、ad转换、时钟ds1302、ds18b20、数码管、液晶显示器操作等等，是学习51的好程序-Summary of each module microcontroller 51 drives. Including eeprom, serial port, infrared decoder, ad conversion, clock ds1302, ds18b20, LED, LCD display operations, etc., i
uCOS-II
- 基于ucos-ii的两个简单实例，并有Protuse仿真。一个是LED实例，还有一个是串口实例。适合于初学者学习。-Based on ucos-ii two simple example, and have Protuse simulation. One example is LED, and a serial port is an example. Suitable for beginners.
UCOSstart-Key
- 这是UCOS在ARM7上的按键仿真（proteus）,自己测试完全可以实现，比如用一个发送"按钮”启动LED闪烁或者串口任务。-This is UCOS ARM7 buttons in the simulation (proteus), his test completely realized, such as using a send "button" to start LED flash or serial task.
new_bord_TX_10bitX2_2_5G
- Xilinx VirtexII-pro 的开发板工程文件，它是在ISE开发环境中实现的。连接有RAM、串口、LED灯、Camera-link接口等，实现的从工业相机到光缆的转换。-xilinx virtex2-pro project,camera-link
URAT
- 一个简单的串口通信汇编程序，通过上位机发送控制信号控制单片机LED灯的点亮与否。文件有protues仿真电路与hex文件。调试时请下载串口调试助手，端口Com1，波特率96-A simple serial communication assembler, through the host computer sends control signals control the chip LED lamp is lit or not. Documents protues Simulation ci
0000998q
- LED 点阵 上位机 VB 16X64 点阵屏串口发送-LED dot matrix PC VB
linux-examples
- 主要包括基于ARMlinux应用程序开发实例，包括LED测试，PWM控制蜂鸣器，串口编程，UDP网络编程-Including application development examples based on ARMlinux , such as the LED test, PWM control buzzer, serial programming, UDP network programming
ABMCI
- 甲机通过串口控制乙机LED闪烁 45 甲机通过串口控制乙机LED闪烁-45 甲机通过串口控制乙机LED闪烁
main
- 利用stm32单片机，对I2C和串口通信做测试，通过LED灯来显示-The stm32 MCU, I2C and serial communication test, LED lights to display
DSP-2407
- DSP 2407的几个C语言程序，包括串口，led等-DSP 2407, several C-language program, including serial ports, and LED
ledPinterrupt
- 在友善之臂的代码基础上进行了修改：能够产生中断，按键1按下时，led1和4亮；按下按键2，led2和3亮，同时在串口显示哪个键按下了。 解决中断在SDARM中不能进行的原因。-S3C2440 led interrupt
serial_control_LED
- Arduino讲座用串口通信发送数据控制LED点亮-Arduino Lecture serial communication to send data control LED light
V0.7
- 控制LED灯的小程序，本来为DMX512写的，现在改为一般串口控制-Control LED lamp of small procedures, originally written for the DMX512, now changed to general serial control
C8051f410-serial-design
- C8051f410串口通信接口设计实验 /串口编程--接收PC发过来的字符串,回发字符串.发送期间中断控制LED灯闪烁 //采用外部晶振22.1184MHz 使用定时器1,方式2产生波特率,SMOD = 0或者1 -C8051f410 serial communication interface design experiments
dancer
- 在dos下写的汇编程序。通过串口控制实验板上的矩阵键盘进行操作，模拟跳舞机，并由LED数码管显示。-When the program starts, the LED digital display the word "HELLO" waiting for players to press any key to start dancing. After the start of the game, alternating the left of the two digital tube displ
2intauart
- LPC2000 中断和串口程序，ARM开启两个中断源Eint1与Eint2，分别用一个按钮来控制。在没有中断的时候两个LED都缓慢闪烁，当任何一个中断被出发的时候，对应的LED会急促闪烁，逐渐回复正常。 此外，使用一个串口来发送当前状态，在无中断的时候发送正常状态报告，当有中断的时候，串口发送中断源。 -lpc2000 interrupt and uart proc，tow interrupt resorces and seperately control tow led2 and se