搜索资源列表
LED
- 1设计要求 PC6,PC7,PD6,PD13 LED快速交替闪烁。 2 硬件电路设计 在开发板上通用I/O口PC6,PC7,PD6,PD13作为控制D1,D2,D3,D4的控制线。 3软件程序设计 根据设计任务要求,软件程序主要包括: (1) 配置GPIO口,将PC6,PC7,PD6,PD13配置为上拉输出模式。 (2) 延时控制相应端口的置位和复位。 4 运行过程 (1) 使用Keil uVision3 通过
8051Pproteus-135
- 《单片机C语言程序设计实训100例——基于8051+Proteus仿真》案例压缩包 第 03 篇 综合设计 35 光耦控制点亮和延时关闭照明设备-" Microcontroller C Programming Language Training 100 cases- based on 8051+ Proteus simulation," Case No. 03 archive 35 optocoupler integrated design control and delay
7-3
- ns中用于无线网络的仿真,并求得了无线网络的丢包率,延时时间等性能指标。-ns in the simulation for wireless networks and obtain a wireless network packet loss rate, delay time and other performance indicators.
WBDBF_Send
- 宽带发射波束形成仿真,16通道,合成角度可以让您以选择,观察角度也可以任意选择。选择了模拟延时线,并仿真了模拟延时线的量化误差。-the code is about WBDBF,it simulate the quantilization error effection of TDU.
Beamforming
- 三个基于延时的波束形成程序,在声纳、雷达等领域有广泛应用,能正常运行,都有仿真图,推荐下载-Three delay-based beamforming codes,have wide applied in sonar, radar and other areas,all of them have the simulation graph, it is recommended to download
delay
- 单片机1ms精确延时的c语言实现,for循环,已经通过keil仿真计时验证,-The microcontroller 1ms accurate delay c language, for circulation, has been verified by keil simulation timing
fast_adder
- 设计了一个超前进位加法器,仿真结果正确,综合结果延时小-fast adder
LM4229_Delay
- LM4229延时程序 240*128液晶显示器 含proteus仿真图-The LM4229 delay the program 240* 128 LCD display with proteus simulation in Figure
msk
- msk的matlab调制与解调仿真,使用延时相干解调方式,包含差分编码与解码模块-modulation and demodulation of msk of Matlab simulation, delay Demodulation, including differential encoding and decoding modules
shumaguan
- 单片机MCS51环境下的PROTUES 仿真,特别要注意的是消隐和延时-SCM the MCS51 environment under PROTUES simulation, with particular attention to the blanking and delay
delay_correlatin_OK
- 这是一个用在数字预失真系统中的延时估计算法matlab程序,已经通过仿真实现。-this is a matlab program of delay estimation algorithm which uesd in the digital predistortion system,and it has accomplish the function.
Tdiaantikonggh
- 本设计是本人的课程设计,一种基于VHDL的电梯控制器的设计,能够实现12层电电梯控制,上下开关,关门延时,提前关门,状态显示出来,通过波形仿真进行观看结果 -The design is my curriculum design, based on VHDL design of the elevator controller to achieve the 12-layer electric elevator control, and switch up and down, closing de
CHAPTER4
- PIC单片机的中断函数 有仿真PIC单片机的延时函数-The delay of the PIC microcontroller interrupt function the delay of the simulation PIC microcontroller interrupt function have simulation
mqst
- 用Verilog HDL编程实现曼切斯特编码器的功能,程序结构简单,仿真后波形延时这方面也进行了相关的优化-verilog HDL
duojingyanshi
- 源信号加多径延时和噪声的仿真,还有其相关性分析,很有用的。-Source signal and multipath delay and noise simulation, and the correlation analysis, very useful
88
- 8x8点阵的程序,横向列向都有锁存,压缩包中有proteus仿真,请注意文件延时。-8x8 dot matrix program, two latches for each edges
trace
- 针对无线传感网络的仿真trace文件,利用gawk进行延时,吞吐量等分析-For wireless sensor network simulation trace file, use gawk to delay, throughput analysis
WENKONG
- 光耦控制点亮和延时关闭照明设备 文件包含PROTEUS 仿真图 KEIL源程序 -Optocoupler control lights and delay off lighting equipment PROTEUS simulation map file contains the source KEIL
ADC0804
- 模数转换器ADC0804操作源程序,Proteus仿真图。同时含有数码管显示文件可显示任意四位数,几个精确延时函数-ADC ADC0804 operation source, Proteus simulation map. Documents containing both digital display can display any digit, a few precise delay function
GPIO
- Keil基于LPC2138的程序设计与电路仿真 1. GPIO程序设计与电路仿真 使用P0.0~P0.7的输出功能来控制LED闪烁。采用灌电流的方式驱动LED,即输出低电平时控制LED点亮。 首先运用PINSEL0、PINSEL1寄存器设置所有引脚连接GPIO,使用IO0DIR寄存器设置P0.0~P0.7为控制输出口,运用IO0SET寄存器进行置位操作,通过使用while、for循环语句,同时调用延时程序,利用清零寄存器IO0CLR、置位寄存器IO0SET交替进行操作,驱动L