搜索资源列表
Digitalpotentiometer
- 基于AD8402的数字电位器，可以拟补模拟电位器进度不够的缺陷，从而提高系统的精度-AD8402 based on the digital potentiometer, can fill to simulate the defects, schedule enough potential to improve precision of the system
PIC_MCP41010
- 数字电位器MCP41010与单片机的连接.驱动程序。需要的话可以做个参考-MCP41010 digital potentiometer connected with the microcontroller. Driver. If necessary you can be a reference to
A_D_translate
- 利用实验板上的ADC0809做A/D转换器，实验板上的电位器提供模拟量输入，编制程序，将模拟量转换成二进制数字量，在数码管的最高两位显示出数字量来。另外要把模拟量值在数码管的最低三位显示出来。例如显示“80 2.50”（ 其中80是采样数值，而2.50是电压值。要求程序可连续运行以便测量不同的模拟电压（类似于电压表） （注意：多次采集求平均值可提高转换精度） -Experimental board do ADC0809 A/D converter, test board provides
ad
- 配置单片机的A/D转换器模块，使其对D2区的电位器进行采样，采样结果显示在数码管上。满量程电压为3.3V时，10位A/D的分辨率大约为3mV，由于受噪声影响，A/D采集的数值会出现噪声，尝试添加数字滤波算法，降低噪声的影响。-Configure MCU A/D converter module, so pairs of D2 region potentiometer sampled, the sampling results show that in the digital pipe. Full
MAX5400Drive
- 利用MEGA16中的SPI总线实现对数控电位器MAX5400的控制，每写入一个新的值便可得到一个新的电阻值-The use of the SPI bus MEGA16 achieve MAX5400 digital potentiometer control, each write a new value can be a new resistance value
ADC0832
- cpu为STC89C52RC。利用ADC0832进行模数转换并且在数码管上显示，调节电位器得到模拟电压。-cpu for STC89C52RC. ADC0832 carried out using analog-digital conversion and digital tube display, adjust potentiometer to be the analog voltage.
adda0808
- 可将电位器上的模拟电压变为数字量输出，并显示！-Can be simulated on the potentiometer voltage into a digital output, and display!
c8051adcuartkeydac
- (1) ADC&UART: 摘 要：本文件是AD采样及串口测试程序；AD输入端子(J7)可输入8路AD(AIN0--AIN7)，另有1路可测量片内温度，9路采样值都通过串口（使用串口必须将JP3的1，2及3，4脚短路）发送出去，在串口调试助手上看观察其值。8路AD输入中AIN7可通过跳以器(JP1)“ADC”（1，2脚短接）与板上电位器相连，通过手动调VR1可以观察到电压值的变化。 (2) KEY&DAC: 摘 要：本文件是键盘及DA输出测试程序；DA输出端子(J9)
ServoPotentiometer
- Controlling Servo with potentiometer ( Atmega 32 )
potentiometer
- control potentiometer to get en pulse output-control potentiometer to get en pulse output
displayvc
- 本程序为改进版10位ADC采样电位计数据串口VC动态显示程序，在原版基础上增加了"查看当前数据"的功能，非常适合学习VC串口动态显示数据的初学者学习.-This program is an improved version of 10-bit ADC sampling data port VC potentiometer dynamic display program, based on the increase in the original " View the current da
MCUcontrolADN2850
- 通过MCU控制ADN2850来完成对于数字电位器的控制-Through the MCU control ADN2850 to complete control of the digital potentiometer
example_1_dc
- // This program provides simple DC motor control using the PCA 8-bit PWM Mode. // The ADC is used to read the potentiometer voltage on P0.6. The ADC uses // polled mode and 64 sample averaging. The 8-bit PWM is configured to operate // at 24 kH
Potentiometer
- potentiometer experiment
SPI
- design and implement a digital system on the Altera NIOS board which will read an analogue input using MicroChip’s SPI MCP3202 12-Bit A/D converter. The 8 most significant bits of the converted data will be displayed on two seven segments of the NIOS
Test06_ADC
- 对nxp-LCP2478板子上的电位器输入的电压进行AD转化后输出，并在串口段进行监视！- Carries on after on the nxp-LCP2478 board s potentiometer input s voltage AD transforms outputs, and carries on the surveillance in the serial port section!
use-MCU-tocontrol-Potentiometer-
- 数字电位器与单片机接口代码程序，包括电路，数字电位器资料。-the way to use MCU to control potentiometer
Digital-potentiometer-adjustment
- 此程序是基于stc单片机的控制数字电位器MCP41010的程序，并带有protues仿真图。-This procedure is based on stc microcontroller MCP41010 digital potentiometer control procedures, and with protues simulation Fig.
BLDC-6-LOAD-PWM-Speed-Potentiometer
- 用keil4编译的stm32单片机开发的电位器调速的BLDC控制程序-Compiled by keil4 stm32 MCU development of potentiometer speed of BLDC control program
BLDC-3-LOAD-PWM-Speed-Potentiometer
- 用keil4编译的电位器3路调速pwm控制的BLDC控制电路-Keil4 compiled with potentiometer 3-way control BLDC pwm speed control circuit