搜索资源列表
URAT_VHDL
- FPGA采用模块工程文件QUARTUS II工程、ADC0809、电机控制PWM、LCD12864显示控制、UART_VHDL-FPGA module QUARTUS II project engineering documents, ADC0809, motor control PWM, LCD12864 display control, UART_VHDL
adc0809dac0832control
- adc0809和dac的共同使用（verilog代码），虽然功能简单，但内容全面，新手原创，共同学习-adc0809 and dac common use (verilog code), although the function of simple, but comprehensive, new original, the common learning
ad0809
- adc0809 转换，verilog代码-adc0809 conversion, verilog code
VerilogProjects
- 在quartus II环境下用Verilog实现了8255, 8253, 8259, 8250, DAC0832, ADC0809等微机接口芯片，硬件设计实验课的作品，有些芯片的功能有所简化，但最基本的功能已实现，有完整的时序仿真波形-In quartus II environment achieved with Verilog 8255, 8253, 8259, 8250, DAC0832, ADC0809 and other computer interface chip, hardware
ad0809
- ADC0809 verilog-ADC0809 verilog...............................
verilogadc0809
- verilog adc0809控制器FPGA实现，编译通过，系统时钟分频，满足ADC时钟要求。-verilog adc0809 controller FPGA, compiler, system clock frequency to meet the requirements of ADC clock.
ADCODE
- 用FPGA控制双ADC0809读写，用于双AD热备控制，用verilog实现-FPGA control with dual ADC0809 read and write, hot standby control for double AD, with verilog implementation
adc
- 设计ADC控制器，Verilog代码.利用有限状态机设计方法在FPGA上设计ADC0809的接口控制器，采样结果送到数码管显示出来。-ADC controller design, Verilog code using finite state machine design in the FPGA design ADC0809 interface controller, the sampling results to the digital display.
ADC0809
- ADC0809为8位AD,程序为利用FPGA实现ADC0809对于信号的模数转换。-ADC0809 8-bit AD, procedures for the use of FPGA implementation ADC0809 analog to digital conversion for the signal.
ADC0809
- AD0809芯片的Verilog hdl驱动程序,-AD0809 the Verilog program
64697923ADC0809_VHDL_ctrl
- 数模转换控制器ADC0809的verilog代码-the verilog code of ADC0809
DAC0832
- DAC0832的Verilog代码，适用于与ADC0809同时学习，效果明显！-DAC0832 Verilog code, applicable at the same time with ADC0809 learning, the effect is obvious!
AD_OK_auto
- ADC0809 FPGA verilog
ADC0809
- ADC0809的verilog实现 及仿真的文件 和仿真的波形图-ADC0809 implementation and simulation of verilog files and simulation waveforms
adc0809
- ADC0809转换器的verilog版本,运用在ISE上，直接可用（注意没有考虑频道问题），结果显示在数码管里（十进制）-Verilog version ADC0809 converters, used in the ISE, directly available (note does not consider channel problems), the results are displayed in the digital tube (decimal)
adc0809
- 1、用状态机设计A/D转换器ADC0809的采样控制电路，并在数码管上显示转换结果； 2、设置有复位和启动/保持开关，要求 ⑴ 复位开关用来使A/D转换器复位，并做好A/D转换准备； ⑵ 启动/保持开关用来控制A/D转换器开始连续转换或停止转换保持结果，即按一下启动/保持开关，启动A/D转换器开始转换，再按一下启/停开关，停止转换并保持结果。 3、采用Verilog HDL语言设计符合上述功能要求的控制电路。-1, with the state machine design A/
ADconversion
- Veriloghdl 代码使用ADC0809来进行ad转换，使用verilog hdl程序来进行ad转化-Veriloghdl ad code uses ADC0809 to convert, using the verilog hdl program to ad conversion