搜索资源列表
RfCtrl
- MCS51的实现无线接收发送（315M或433M)源程序代码。-MCS51 the wireless receiver send (315M or 433M) source code.
AV_RXD_506AM_00AAH
- 无线接收发送来的GPS压缩数据流，并解码出经纬度速度GPS状态等信息，与GPS无线发射程序配合使用-wireless receiver to send the GPS data stream compression and decoding speed up GPS coordinates for the state, and other information, wireless and GPS launch procedures with the use of
RADIO_RE
- 这个源代码是关于MCS-51的无线接收，用89S52控制MT8870B进行DTMF解码。程序相当的经典，本人调试了几周后，达到了非常好的效果。误码率相当的小。我觉得好东西要大家分享的，所以今天我上传此代码，与大家共同分析进步。-the source code is on the MCS-51 wireless receiver, S52 control with 89 MT8870B for DTMF decoder. Quite the classic procedure, I debug a
CC1100.rar
- 单片机通用串口uart接收与发送无线信息，实现无线接收。,MCU Universal Serial uart receive and transmit a wireless message, wireless receiver.
send.rar
- easyARM1138驱动nRF2401A无线接收，IAR开发环境,easyARM1138 drive nRF2401A wireless receiver, IAR development environment
Wireless receiver 无线接收的例程
- 本程序写的是无线接收的例程，介绍了无线解码。-This procedure is written in wireless reception routines, introduced wireless decoder.
wuxianyaokong
- 将无线接收模块按照脚位对应插入学习板无线插座注意，不要插错，否则会损坏模块学习板学习板处于正常工作状态D3，D2，D1，D0 ，LED灯亮起，将程序tanst.hex 下载 到学习板程序在配套光盘HZC51学习板使用教程HZC51学习板实验程序无线遥控程序无线遥控里面，下载完后，数码管显示0000按遥控发射器A键，此时遥控器红灯亮起，并发出编码信号，学习板，收到信号并解码并驱动数码管显示4000分别按遥控器B，D，C键，学习板分别显示此遥控器发射距离开阔地可达到100米-The wireless
WirelessMouse
- 无线鼠标发射和接收模块源代码，支持对码和跳频的成熟方案，可以直接应用。-Wireless mouse transmitter and receiver module source code, support for the binding and frequency hopping can be applied directly.
EV1527-PIC
- 无线接收解码源程序。 可学习解码。锁存输出功能。-Wireless receiver decoder source code. Can learn decoding. Latch output.
wireless_exa1
- nrf2401无线模块的at89s52的接收发程序，实现无线传输数据-nrf2401 wireless receiver module at89s52 hair procedures, wireless transmission of data
transmitter_receiver
- 在matlab环境下，对无线通信系统的发射机和接收机信号传输进行仿真-In the matlab environment, on wireless communication system transmitter and receiver signal transmission simulation
Wireless remote control system for towercrane base
- W ireless rem ote control system for tower crane based on M SP430 and nRF905：介绍了一种基于无线遥测技术的塔吊遥控系统，该系统以MSP430超低功耗l6位微控制器和无 线收发芯片nRF905为核心。系统采用软件编码和硬件译码的方式提高了系统的抗干扰能力，系统发 射器采用定时扫描、接收器采用无记忆输出控制方式，提高了系统可靠性，该系统可广泛应用于塔吊等 一般的工业遥控系统中。-W ireless rem
WirelessRecv
- 基于无线单片机nRF9E5的无线接收程序，实现开关量的无线串口通讯。编成环境KEIL-Based on the wireless single-chip wireless receiver nRF9E5 procedures, to achieve switching capacity of wireless serial communications. Into the environment KEIL
PrincipleCellPhone
- 手机基本原理: ETACS、GSM蜂窝手机是一个工作在双工状态下的收发信机。一部移动电话包括无线接收机(Receiver)、发射机(Transmitter)、控制模块(Controller)及人机界面部分(Interface)和电源(Power Supply)。-The basic principles of mobile phones: ETACS, GSM cellular phone is a work in the duplex state of the transceiver. A m
CC1010Chip
- 无线龙ZigBee模块CC1010的接收－发送程序。-Liuzhou ZigBee wireless receiver module CC1010- Send procedure.
QPSK_8PSKProject
- This project simulates the operation of wireless digital communications using Q-PSK and 8PSK modulator. The project consists of four steps: transmitter design, channel propagation effect, receiver design and finally measuring system performance.
SECURED-WIRELESS-COMMUNICATION
- This project is used to communicate or transmit a text message from one place to another place through wireless. The text message is encrypted by using the Microcontroller and the encrypted message was transmitted through wireless. At the receiver en
Cooperative Diversity in Wireless Networks
- 无线网络的中继节点协作分集研究源代码，包括多种接收端技术-Relay nodes in wireless networks of cooperative diversity source code, including a variety of receiver techniques
wireless-receiver
- 用C语言实现无线遥控接收模块实验，可立即运行。需要外籍C-52型单片机-Wireless remote control receiver module experiment C language, and can be run immediately. Need foreign C-52 type microcontroller
USRP-Packet-Receiver
- 基于labview开发环境实现的数字无线接收机，该接收机的实现需要借助于硬件USRP-A realization of the digital wireless receiver based on LabVIEW development environment,the receiver needs to achieve the hardware USRP