搜索资源列表
GPRS_Q2403
- arm下驱动WAVECOM模块Q2403的源代码，包括拨打电话，发短信，串口中断接收发送等！-arm driving under Enfora Flash Card module source code, including telephone calls and send text messages, send interrupt reception so!
315M无线通信模块
- 315M的无线通讯模块，用VC编写(1) 串口初始化,如何设置波特率,串口的四种工作方式。 (2) 串口查询、中断方式发送程序编写方法 (3) 串口查询、中断方式接收程序编写-- 315M wireless communications modules, prepared with VC (1) serial port initialization, how to set up a baud rate, Serial four methods of work. (2) Serial inquir
dsp_SCI
- dsp串口通讯，采用中断方式实现接收和发送功能-dsp serial communications using interruption means receive and transmit functions
comm
- DOS下使用中断方式接收发送完整数据源码
200609-151
- 函数名称： UART_init()串口初始化函数 // 函数功能： 在系统时钟为11.059MHZ时，设定串口波特率为9600bit/s // 串口接收中断允许，发送中断禁止
IntSerialComm
- 中断方式实现串行接收发送数据，注释规范，不可多得啊
汇编串口
- 本程序是通用同步和异步串行接收器和转发器(USART)在异步状态下使用中断 * 方式进行全双工接收和发送数据的通信程序。共包括下面列表中这四个子程序。这 * 四个子程序的具体使用方法请参考各自的说明。-this procedure is common synchronous and asynchronous serial receivers and transmitters (USARTs) in the state to use asynchronous interrupt * for ful
CaN总线
- CAN总线通信 CAN2.0A 1号编码器 接线： CS====P2^7//片选 A0-A7=P0.0-P0.7//数据口 INT===INT0（P3^2）//接收后产生中断 BasicCAN模式 中断接收：标准数据帧、标准远程帧。 发送：标准数据帧 ID码：01 数据：发送前2个字节 10位编码器 最大1023 上位机显示 03 FF
SDIO_Driver.rar
- SDIO设备驱动。介绍了如何利用总线驱动，使SDIO设备初始化，接收中断，发送和接收数据等操作。,SDIO device drivers. Describes how to use bus driver, so SDIO device initialization, interrupt reception, send and receive data such as operation.
MYSerialPort
- 用CserialPort类实现的串口中断接收程序，并可发送字符串。可多串口操作。-With CserialPort class implements the serial interrupt reception process, and send the string. Can be multi-serial operation.
AVR-USART
- avr usart/uart 通讯，中断接收，循环中发送-avr usart communication
interrupt
- 实验实现串口中断实验，通过中断和计算机进行通信 * 首先接受联机信号，然后接受计算机的相关控制信号 * 本实验中，采用发送不同的字符给计算机来模拟接收到的不同的计算机控制命令 * 通过扩展，可以实现不同的功能 *-Experimental realization of serial interruption experiments, carried out through suspension and computer
URAT
- 串口接收1字节数据，然后发送出去1字节 使初学者领略使用中断进行数据通信-Serial port to receive one byte of data, then send out one byte enables beginners to enjoy the use of interruption of data communication
UART
- UART中断串口通讯，通过两个外部中断来控制数据的发送-UART serial port interrupt communications, through two external interrupt to control the data sent
comrxtx
- 本程序是在DOS环境下实现TURBOC串口编程。其主要功能是实现中断接收功能和发送功能-This procedure is in the DOS environment to achieve TURBOC serial programming. Its main function is to achieve the interruption of receiving and sending functions
C8051
- C8051F系列单片机串口通讯程序，串口编程--接收PC发来的字符串,回发字符串.发送期间中断控制LED灯闪烁-C8051F series single-chip serial communication program, serial programming- PC sent to receive the string, back-fat string. Sent during the interruption of control blinking LED lights
LSD-TEST430F5438-01-CRC1.c
- ** 串口初始化顺序： ** 1、置位UCSWRST ** 2、配置UCAXCTL0、UCAXCTL1 ** 3、波特率设置 ** 4、使能接收或发送中断-** Initialize serial order:** 1, Set UCSWRST** 2, configuration UCAXCTL0, UCAXCTL1** 3, the baud rate settings** 4 so that it can receive or send interrupt
sdds
- 单片机C51串口中断接收和发送测试 单片机C51串口中断接收和发送测试 单片机C51串口中断接收和发送测试 -C51 microcontroller serial port interrupt to receive and send a test MCU C51 serial port interrupt to receive and send a test MCU C51 serial port interrupt to receive and send a test MCU C51 seri
scififointerrupt
- dsp源码，实现SCIFIFO功能的中断发送和终端接收8个字节发送，8个字节接收-dsp source, the interrupt function to achieve SCIFIFO sending and receiving terminals to send 8 bytes, 8 bytes received
下位机程序111
- 进行串口读取数据，中断服务，完成一定的脉冲发送(Serial read data, interrupt service, to complete a certain pulse to send)