搜索资源列表
shumaguanxianshi
- 利用动态扫描和定时器1在数码管上显示出从765432 开始以1/10秒的速度往下递减直至765398并保持显示此数 与此同时利用定时器0以500MS速度进行流水灯从上至下移动 当数码管上数减到停止时,实验板上流水灯也停止 然后全部开始闪烁3秒后(用T0定时) 流水灯全部关闭数码管上显示出“HELLO”。到此保持-have not
miaobiao1
- 用动态扫描方法和定时器1在数码管的前三位显示出秒表 精确到1 秒,即后两位显示1 秒,一直循环下去。实现按第一个键秒表停止计数,按第二个键开始计数,按第三个键清零-have not
shumaguananjian
- 介绍CH452芯片功能,CH452驱动,数码管显示,按键扫描-CH452-driven, digital display, keypad scanning
keyboardscannner
- 汇编语言实现了4*4的程序扫描,并输出相应数码管的显示-Assembly language to achieve a 4* 4 scan, and output a corresponding digital tube display
4_2
- 用动态扫描方法和定时器1在数码管的前三位显示出秒表, 精确到1 秒,即最后一位显示1 秒,一直循环下去 设时钟频率为12M-Dynamic scanning method and a digital timer control of the top three shows a stopwatch, accurate to 1 of the second and final one showed 1 of the second, has been set clock cycle con
C51_Source
- 51单片机源程序:1-流水灯、2-数码管动态扫描、3-数码管移动、4-输入输出口、5-喇叭、6-按键程序、7-定时器0、8-定时器1、9-中断、12-红外测试、14-24c02_EEPROM读写、21-红外解码数码管显示-51 MCU source: 1- water lamps, 2- Digital control dynamic scan, 3- digital tube mobile, 4- input and output ports, 5- Speaker, 6- key progr
c_dpjcx
- 定时中断处理函数,键盘扫描函数,数码管显示函数-Timer interrupt handler, keyboard scan function, LED display function
dongtaicuanhangxianshi
- 动态串行显示,数码管动态扫描,自动计时,清零,暂停-Dynamic serial display, the digital dynamic scanning, automatic timing, clear, pause
44keyboard-scan-in-FPGA
- Verilog语言的四乘四的键盘扫描程序。共阴共阳级数码管均能显示。-4 multiply 4 keyboard scan in FPGA
shumaguan
- 多位数码管分别显示不同数字,这种扫描显示方式成为动态扫描,并不停变化赋值-Many digital tube display different numbers, this scan display dynamic scanning, and ever-changing assignment
TM1638
- 在单片机上有TM1638来控制数码管和对键盘的扫描并可以再数码管上显示出来-TM1638 digital control and keyboard scan digital tube displayed in SCM
led
- led显示程序,包括键盘扫描的驱动线、所有数码管显示都为8,只有数字1在各个数码管之间循环闪动-led s display program
xiaoyin
- 51单片机驱动数码管时应该会出现有阴影的情况,本程序通过调节扫描函数达到了消除阴影的功能-There will be a shadow of the situation should be 51 singlechip driver digital tube, this program by adjusting the scanning function can eliminate the shadow function
dd12345678
- 这是一个简单的实验程序,主要是利用数码管动态扫描显示12345678-Use of digital dynamic scanning display 12345678
VHDL_book1
- gate:基本逻辑门的实现和验证 mux4_1_gate:多路复用器的门级实现和验证 mux4_1_behav:多路复用器的行为级实现和验证 seg7_gate:7段数码管逻辑门实现和验证 seg7_behav:7段数码管case语句描述和验证 mux7seg:采用按键复用7段数码管的实现和验证 clkseg7:采用时钟自动扫描复用7段数码管的实现和验证 comp4_gate:4位比较器结构化实现和验证 comp8_behav:8位比较器行为实现
new
- 这是一个基于51单片机的六路抢答器C程序,包括按键扫描程序,八位数码管程序,蜂鸣器程序等。-This is a 51 microcontroller-based six-way Responder C program, including key scanner, eight digital tube procedure, buzzer procedures.
juzhenjianpan
- verilog写的一个5乘5键盘扫描程序,并可以利用数码管实现对于的0到24的显示-verilog to write a 5 x 5 keyboard scanning procedures, and can be implemented for the use of digital tube display of 0-24
ex63
- 四位共阳数码管快速扫描显示1,2,3,4-Four common anode LED display 1,2,3,4 quick scan
Digital-tube-dynamic-scanning
- 这个针对C51编写的数码管动态扫描的源代码-The digital tube dynamic scan source code
duogongnengshuzibiao
- 多功能数字电子表 (1)正常计时:秒(60)、分(60)、小时(24)计数;秒计时的频率为1Hz,数码管用动态扫描实时显示计时的小时、分、秒。 (2)整点报时:逢整点蜂鸣器在“59”分钟的第51、53、55、57秒发频率为512Hz的低音,在“59”分钟的第59秒发频率为1024Hz的高音。 (3)校时: 校小时, 显示小时数码管以4Hz的频率递增计数; 校分, 显示分数码管以4Hz的频率递增计数; 校秒, 秒清0。 其他: 1.晶振为12 MHz 2. 采用