搜索资源列表
usb_flash
- 优盘程序,符合USB1.1规范。硬件平台：ATmega162+PDIUSBD12+K9F5608。软件平台：ICCAVR。协议：Bulk-Only Transport,Reduced block command.-Youpan procedures, in line with standard USB 1.1. Hardware platforms : ATmega162 PDIUSBD12 K9F5608. Software platform : ICCAVR. Agreement : Bul
A1200TelnetGzbFjTnzgclB
- A1200 Telnet 在刷机＋破解补丁后，手机支持Telnet。在安装MPKG，通过MPKG安装上Loader，可以下载USBLAN驱动： 把下载的A1200 Telnet.rar里的文件解压到一个临时目录里，双击install.bat。这一步是先拷贝A1200的USB LAN的驱动。 手机Modem模式连接电脑，点击Loader笑脸图标，电脑上将发现新硬件，驱动指向到临时目录里，安装A1200的USB LAN驱动。在安装成功后，在cmd命令行下，输入命令ipconfig，
dpjcx
- 使用PIDUSBD12芯片实现的usb接口程序，符合usb1.1协议，可以实现DMA传输，和命令控制传输。-PIDUSBD12 chip using the usb interface procedures, in line with the USB1.1 agreement can be achieved DMA transfer, and command control of transmission.
reader
- Test some scsi command for usb mass storage
37724133zhongxing_phone_ATcommand
- At command set for zte usb cdma modem extract using win ran or any other means to see the file
USB-CHECK
- 可用于检查USB DEVICE设备信息。VC开发。编译后CMD命令行运行。简单易用。-Can be used to check the USB DEVICE device information. VC++. CMD command line to run the compiled. Easy to use.
bulkonly.c.tar
- UsB Commands for command block wrapper and command block status-UsB Commands for command block wrapper and command block status
usb7325-control
- USB7325 CONRTOL ,主要实现了USB7325数据卡的数据采集和指令发送等。-USB7325 CONRTOL, main achievement of the USB7325 data card for data acquisition and command transmission and so on.
USB_SPI
- 我自己写的．在stm32f103c8上实现ＵＳＢ稳定通信．该项目很简单．根据ＵＳＢ上获取的命令通过ＳＰＩ接口与外部设备操作．请使用该ＵＳＢ程序时写出出处．谢谢！-I wrote it myself. USB to achieve stability in the stm32f103c8 communication. The project is simple. Acquired under the USB command on the interface with external device
CPPBuilder_HidUSB
- C++Builder中，通过HID_GUID找到HID USB设备，并向咖啡机设备发送命令以取得咖啡机设备的参数。深圳企业www.wik.com.hk公司的咖啡机项目基本源代码。-In C++ builder, through HID_GUID to find HID USB device. and Send command to Coffee Machine to get the parameters of Coffee Machine. Project in ShenZhen industr
USBIsoSourceSink
- USB3.0 中断传输固件，主要匹配上位机程序，可以响应上位各个命令-USB3.0 interrupt transfer firmware, the main host computer matching program that can respond to the position of each command
QT5
- 为了实现电润湿器件的驱动和控制，该系统设计包含驱动电路和上位机软件两部分。驱动电路使用PIC单片机通过FT245组成的USB接口模块接收上位机的控制命令，按照预定义的格式解析生成控制信号控制DA芯片AD5535输出电压信号，使用集成化的电压芯片实现电平转换和升压电路;上位机软件基于Qt软件开发框架在Windows平台下采用C++语言编写，实现对驱动参数的各种操作和电润湿器件电极的状态显示满足经实验验证，该系统工作性能良好(In order to achieve the drive and con