搜索资源列表
MCU
- 超声波测距传感器-如何DIY一个属于你的超声波测距传感器。
V2
- 超声波测距电路图 以及超声波传感器驱动电路-Ultrasound
CSB
- DIY一个属于你的超声波测距传感器程序的构思和设计-DIY a part of your Ultrasonic Ranging Sensor concept and design procedures
chaoshengbodaocheleidaolibao
- 利用SPCE061A单片机、三个超声波测距模组实现超声波倒车雷达,要求具有下述功能: 1. 可以语音提示模组探测范围内的0.35m~1.5m范围内的障碍物; 2. 语音提示可指明哪一个方向(或区域)有障碍物在探测范围内; 3. 利用三个LED发光二极管表示三个传感器探测范围内是否有障碍物,当在探测范围内有障碍物时,发光管以一定频率闪烁,闪烁的频率以距离定,距离越近频率越高。-Use SPCE061A Singlechip, three Ultrasonic Ranging modul
document
- 硬件: 1. 车体 2. S3C2410A开发板 3. 红外测距传感器 4. 伺服器(舵机) 5. 直流电机 6. 电机驱动板 7. 电源 软件: 1. Linux2.6.14内核,包括:Nand Flash、USB、NET、PWM、ADC等驱动;Yaffs等文件系统。 2. VIVI 3. Busybox1.6 主要目标: 使车体能自主地在平地行驶,能躲避一定高度和大小的障碍物。 -Hardware: 1. Carbody 2
Rangefinder
- 利用超声波传感器设计价格低廉、近距离测距器-The use of ultrasonic sensor design cheap, close-range-finder
ceju
- 超声波测距系统软件设计采用模块化设计,由主程序、发射子程序、查蟓接收子程序、定时子程序、显示子程序等模块组成。该系统的主程序处于键控循环工作方式,当按下测量键时,主程序开始调用发射子程序、查询接收子程序、定时子程序,并把测量结果用显示子程序在液晶屏上显示出来。 由于液晶要使用同一P3口,所以必须使用位操作,否则将导致LCD不能正常显示。在系统还可以加入温度传感器来监测环境温度,可进行温度被偿。为了增强系统的可靠性,应在软硬件上采用抗干扰措施。-Ultrasonic ranging system
USED
- 夏普红外传感器GP2D12进行测距所需资料与原理图(手工绘制,传感器接口部分对照传感器的样子即知)已经程序-Sharp infrared sensors for distance measurement GP2D12 schematic diagram with the required information (hand-painted, sensor interface looks like part of the control sensor that is known) has proc
hwcj
- 基于STC89C51单片机的红外测距传感器的应用,涉及传感器应用、AD转换、单片机控制等。-STC89C51 MCU-based infrared sensors ranging applications, applications involving sensors, AD conversion, single-chip control.
EM30919红外传感器C程序
- EM30919红外测距传感器C程序,IIC总线,MSP430单片机
Sensor data processing
- 处理传感器数据的程序,例如测距传感器。去掉一个最大值,去掉一个最小值,然后8个数据取平均值。结果去除了部分噪声,减少了误差。(program that deals with sensor data, such as a range finder. Remove a maximum, remove a minimum, and then take the average of the 8 data. As a result, partial noise is removed and error i
vl53l0x_arduino_master
- GY-530+VL53L0X激光测距传感器模块+ToF测距+飞行时间测距传感器(GY-530+VL53L0X laser ranging sensor module +ToF ranging + time-of-flight sensor)
GP2D12 Infrared distance sensor
- GP2D12红外测距传感器应用,主控平台为51 ,开发环境为KEIL(GP2D12 infrared distance sensor applications, the main control platform for 51, the development environment for KEIL)
GY-53资料v1
- 基于vl53l0x的测距传感器的电路板,应用于0-1.2米测距。(Vl53l0x based range sensor circuit board, applied to 0-1.2 meters distance measurement.)
激光测距基于51
- 使用51单片机,并用激光测距模块测距并在LCD上显示(Distance measurement and display on LCD)
超声波测距资料
- 超声波测距,根据超声波指向性强,能量消耗慢,在介质中传播距离远的特点,利用超生波传感器对前方物体进行感应,经过单片机中的程序对超声波传感器发射和接收的超声波信号进行分析和计算处理,最后将处理结果在LCD1602上显示。(Ultrasonic ranging, according to the strong point of ultrasonic energy consumption is slow, the propagation characteristics of the distance
GY-530VL53L0X激光测距传感器模块
- 激光传感器的源码,gy530vl530l0x(gy530vl530l0x,for stm32f103)
VL53L0X激光测距传感器
- 使用VL53L0X型号激光测距模块测量距离 1.2m内(Use VL53L0X model laser ranging module to measure the distance within 1.2m)
1、STM32L031_硬件I2C_VL53L0驱动
- 激光测距传感器驱动,开发环境MDK,硬件IIC接口,MCU:stm32l031(Laser ranging sensor driver, development environment MDK, hardware IIC interface, MCU:stm32l031)
A60_ESP01A_超声波测距APP
- HC-SR04超声波传感器在单片机上的简单应用,并用esp8266wifi模块实现手机接收测距信息(The simple application of HC-SR04 ultrasonic sensor on single chip computer and the realization of receiving ranging information by mobile phone with esp8266 WiFi module)