搜索资源列表
I2C_of_MSP430F249
- This demo connects two MSP430 s via the I2C bus. The master reads 5 bytes the slave. This is the MASTER CODE. The data the slave transmitter begins at 0 and increments with each transfer. The USCI_B0 RX interrupt is used to know when new data h
SPI_of_MSP430F249
- SPI master talks to SPI slave using 3-wire mode. Incrementing data is sent by the master starting at 0x01. Received data is expected to be same as the previous transmission TXData = RXData-1. USCI RX ISR is used to handle communication with
UART_of_MSP430F249
- Echo a received character, RX ISR used. Normal mode is LPM0. USCI_A0 RX interrupt triggers TX Echo. Baud rate divider with 1MHz = 1MHz/19200 = ~52.1 ACLK = n/a, MCLK = SMCLK = CALxxx_1MHZ = 1MHz
an-r01an1721ej0220-rx-gpio
- 瑞萨RX32T开发板gpio例程，官网下载的版本(renesa RX32T gpio example)
程序
- void main(void) { TMOD=0x01; //设T0为方式1，GATE=1； TH0=0; TL0=0; ET0=1; //允许T0中断 EA=1; //开启总中断 InitLcd1602(); LcdShowStr(0,0,PuZh); while(1) { StartModule(); while(!Echo); //当RX为零时等待
uart
- 基于verilog的fpga串口通信,rx,tx.两根线(Basend on verilog fpga uart tong xin)
步进电机控制
- 本篇说明文档介绍了基于RX/23T单片机的步进电机控制。主要介绍了如何在代码生成工具e2 studio下配置本例程所需要的CLOCK、PORT和MTU等模块并生成相应的驱动代码，同时对生成代码文件添加的步进电机控制、转速调整等功能进行了详细说明。最后附步进电机控制实例。(This document describes the stepper motor control based on RX/23T microcontroller. Mainly introduces how the code
OTU_RXBLK
- cctv otu rx block source
new_simulation
- 通过时钟使普通的IO口模拟UART串口通讯(Use Timer_A CCR1 hardware output modes and CCR0 SCCI data latch // to implement UART function @ 2400 baud. Software does not directly read and // write to RX and TX pins, instead proper use of output modes and SCCI data // la
mii_mac
- mii mac tx and rx，以太网mii接口收发(mii mac tx and rx Ethernet mii interface)
uart_test
- verilog实现UART收发功能，硬件平台为spartan 6，软件平台为ise14.7(verilog implement UART rx and tx function)
SI4463收发程序
- 4463收发程序 SPI 可实现稳定收发 基于STM32F103C8T6(4463 TX RX code MCU IS STM32F103C8T6)
Nrf24l01
- CoIDE full project tx rx test on stm32 and nrf24l01 module
mc251_stm+rfm (1)
- Iar project stm32 and Rfm23, tx and rx sound speex codec.
SI4432-TransferReceived-MODEM-master
- si4432 tx rx modem on arduino board
txrx
- FPGA串口通信的简单示例程序，分为TX和RX两个模块(A simple program for FPGA serial communication)
SX1278 Demo
- sx1278的demo代码,，用stm8s003单片机，发送接收无线循环(sx1278 demo code,with stm8s003 mcu,tx and rx again and again)
AdLabPlus高频设计软件
- 高频设计辅助工具 电气工程软件，高级电机工程实验室。拥有20多个特性工具专为设计网络、传输线、变压器等设计。它也可以计算线圈和变压器和各种类型的过滤器以及运行噪音等。它可以计算RX和TX系统。AdLabPlus包括一个非常强大的Smith曲线图程序。(AdLabPlus contains AdLab/CSmith and features 5 new electrical engineering tools, for instance for designing active and pass
I2C_withoutDMA_SlaveTRX
- STM32F031 I2C Slave TX and RX by MXCube LL，模拟了一块RAM，可读写(STM32F031 I2C Slave TX and RX by MXCube LL)
uart_receiver
- Uart receiver VHDL code