搜索资源列表
st10f166_adc
- This example program shows how to configure and use the A/D Converter of the following microcontroller: STMicroelectronics ST10F166 After configuring the A/D, the program reads the A/D result and outputs the converted value using the serial p
S3C44B0X例子程序2
- 1. beep -- PWM测试 为 ADS1.2 下编译的项目, 在sdt2.51的ADW里调试，该程序运行后在57600的超级终端里按PC机键盘的“+”“-” 按键，可以听到BUZZ增大减小的声音。 2. key -- 按键测试 为 SDT2.51 下编译的项目, 在sdt2.51的ADW里调试，该程序运行后按FS44B0X上的按键key1 key2 key3 key4 相应的发光二极管亮 3 keyint -- 按键中断测试 该项目在SDT2.51下编
S3C44B0X例子程序1
- 5 ledblink -- 跑马灯程序 该项目在SDT2.51下编译调试。最简单的demo程序，运行后3个发光二极管轮流点亮。 6 timerint -- 定时器中断demo程序 该项目在SDT2.51下编译调试。将子目录timerint拷贝到c:\\ 下。 该demo程序的主程序是while空循环，定时器中断服务程序每500ms将3个LED反相。 在57600超级终端里也可以看到中断发生时的信息。 7 uart -- 串口测试程序 该项目在SDT2.5
at91sam7x256_iar
- atmel官方的at91sam7x256芯片在iar编译环境下的全部演示代码，以工程方式提供。-official at91sam7x256 atmel chip iar build environment in the whole of the demonstration code to the project provided.
AnteeoBee_20060218
- his project was built and tested with WinAVR-20060125. Make sure the MCU target define in the Makefiles corresponds to the AVR you are using!! To build the code, just install WinAVR and run \"make\" from the console in echomaster and ech
ALi3355_ClassC1
- ali3355源码: 1.OBJS目录:编译目录 命令: ./clean.sh ./55product.sh 2.serve:光头部份程序 3.source:介面与播放有关项目.-ali3355 Source : 1.OBJS Contents : build directory order : . / clean.sh ./55product.sh 2.serve : Bald some procedures 3.source : interface with the
FFTtable
- tms320c6711-fft 调试环境：code composer studio3.1 采用查表方式对心电图信号进行处理 设置注意：project-build options-linker-stack size 设为5-tms320c6711 - fft debugging environment : composer studio3.1 code look-up table method used to deal with ECG signal installed Notes I
adaptiveFIR
- 自适应滤波 开发环境：ccs3.1 设置事项：project-build options-linker-stack options 500 -adaptive filtering development environment : ccs3.1 set matters : project-build options-linker-stack options 500
sine8_display
- 产生正弦波 开发环境：code composer studio3.1 设置说明：project-build options-linker-stack size 5-generated sine wave development environment : code composer studio3.1 Descr iption : project-build options-linker-stack size 5
dianzu
- 133，134-热敏电阻测试数码管显示功能的演示。基于51单片机，keil建立项目工程，包含全部源文件。-133,134- Thermal resistance test digital display presentation. Based on 51 MCU, keil build project, including all the source files.
Altera_FPGA_develop(QuartusII_7.2_ModelSim_6.5).ra
- Altera FPGA开发说明（QuartusII 7.2 & ModelSim 6.5）.pdf 建立和编译QII项目 modelsim功能仿真 QII引脚分配 modelsim时序仿真（建立Altera仿真库） QII下载 -Altera FPGA Development Descr iption (QuartusII 7.2 & ModelSim 6.5). Pdf project to establish and build QII QII pin ass
EmbededC
- 嵌入式C语言编程教程，从开发环境的设置到项目工程建立，都有详细的讲解-Embedded C programming language tutorial, the settings from the development environment to build project, there is a detailed explanation
lvbo12
- 利用AVR单片机设计IIR 低通滤波器，其中截止频率、抽样频率都有说明，运行环境是先用IICAVR建立工程，再将该代码加入进去即可-Use AVR microcontroller IIR low-pass filter, which cut-off frequency, sampling frequency with specifications, running environment is to use IICAVR build project, then the code can join
build-a-simple-project
- EXCD-1可编程片上系统 实验例程EDK部分 之建立一个简单的工程 -EXCD-1 programmable system on chip test routine part of the EDK project to build a simple
project
- 本程序是DS18B20以及LCD1602的一个实例。编译环境：Keil C51.-This program is an example of DS18B20 and LCD1602. Build Environment: Keil C51.
file-for-building-the-project
- 需要建设某项工程时所需要用到的文件，对建设工程有帮助-Need to build a certain project files needed for construction projects
CCS3.3-build-DSP-BIOS-XDC-project
- 在CCS3.3下建立基于DSP-BIOS和XDC的工程入门资料-CCS3.3 build DSP-BIOS XDC project
project--1
- 这是一个建立工程的文件，使用汇编语言编写，实现led灯的亮灭(This is a project to build the document, using assembly language, to achieve the LED lights out)
project
- stm32的GPIO配置，做小车程序的一个工程模板，不用自己建立工程了,KEIL5可用(STM32's GPIO configuration, as an engineering template for the car program, does not build the project itself, KEIL5 is available.)
F4工程模板
- 基于STM32F4系列，固件库建立的工程，直接可以使用(based on stm32f4 std library build project .)