搜索资源列表
fpga_coder_module
- 本人编写的FPGA光电编码器输入模块,没有实验,但仿真基本实现,希望有参考价值.-FPGA optical encoder input module, there is no experimental, but simulation technology, hope to have reference value.
fhe-pulse
- 光电编码器采集脉冲的程序，采用计数查询等待中断方式， 液晶显示正反转 ,显示脉冲数（60个/转），显示转圈数-optical encoder pulse acquisition procedures adopted count inquiries pending interruption, LCD rotating direction Pulse a few shows (60 / switch), the show moved around a few
MCU2PID
- 使用ICCAVR编辑，配合MCU1使用。 主要进行了增量式光电编码器的脉冲读取，PID控制-use ICCAVR editors, with MCU1 use. A major incremental optical encoder pulse reading, PID control
v_pid
- 使用ICCAVR编辑，配合MCU1使用。 主要进行了增量式光电编码器的脉冲读取，PID控制的头文件-use ICCAVR editors, with MCU1 use. A major incremental optical encoder pulse reading, PID control of the header files
zhuanpan.rar
- 增量式光电编码器输出四分频脉冲计数，分别为A，B两路信号,Incremental optical encoder pulse count output frequency of a quarter, namely A, B two-way signal
coder_counter
- 增量式光电编码器计数器的FPGA实现程序,verilog3段式FSM,异步加载.-Incremental Optical Encoder counter program FPGA implementation, verilog3 struts FSM, asynchronous load.
ZLJISHUQI
- 】文中重点讨论基于单片机的光电脉冲编码器计数器的软件倍频和辨向原理,并从编码 盘条纹和位置检测元件的空间分布原理出发给出了在编码器输出A、B 正交方波的前提下最多只 能4 倍频的结论,最后介绍了集倍频、辨向、计数于一体的单片机计数器原理,该计数器具有消除抖 动误计数、倍频数可选、计数长度无限制的特点-】 The article focused on single-chip-based optical pulse encoder software counter to the prin
H2_3
- 这是光电编码器的汇编程序，希望对学习的人有帮助-This is a compilation of optical encoder procedures, and they hope to learn helpful
statemachine
- 基于状态图的光电编码器4倍频vhdl程序，输入相位差90度的两相，输出倍频和方向信号-Based on the state of the optical encoder Figure 4 multiplier vhdl procedure, enter a 90-degree phase difference of two-phase, frequency and direction of the output signal
STCPS2
- 51光电编码器实现，STC处理编码器的要求，同时编码根据PS/2协议，实现上下键以及确定键。-Optical encoder 51 to achieve, STC encoder processing requirements, as well as coding in accordance with PS/2 protocol, to achieve and to identify the key up and down keys.
52250440605_AB
- 基于CPLD 的光电脉冲码盘 信号四倍频电路设计-CPLD-based electro-optical pulse encoder signals four multiplier circuit design
s_UIC_v3.03.tar
- (IBM) Interrupter Controller for PowePC405 (verilog)
Encoder877
- optical encoder code in c language for PIC16f8-optical encoder code in c language for PIC16f877
WINCE_optical_encoder
- 讲述在WINCE系统下，如何实现光电编码器的驱动程序，很有参考价值。-WINCE about the system, how to achieve optical encoder driver, a good reference.
bianmaqi
- 旋转光电编码器的单片机借口及某型号单片机的c程序，好资料-Rotary optical encoder and a model of SCM SCM pretext c procedures, good information
main
- code for calculat speed of a dc motor with an optical encoder compilateur CCS
JUDU
- 《角度测量器》 用光电编码器测量角度，每个脉冲为 0.72 度。 测量范围：0.0～360.0 度 为保证不错过脉冲，用 timer1计数，在电平跳变中断里判断转动方向，尽量加快处理过程。 数据换算和数码管扫描显示在主循环中实现。 -" Angle measuring device" with the optical encoder measuring the angle of each pulse is 0.72 degrees. Measuring
optical-encoder
- 此为51 8位单片机16 位置旋转编码器的源码，自己编的，keilc 环境下编译，保证能用，编码开关为红外机械式连续旋转。-51 cpu optical source code，16 position
encoder
- 使用VHDL编写的光电编码器。并且在quartus软件进行仿真。最终下载在FPGA板上实现光电编码器的使用。-Optical encoder using VHDL written. And quartus software simulation. The final use of photoelectric encoder download FPGA board.
encoder-c51-program
- IAR 编译器下 51单片机 读取4000线 光学编码器程序-IAR compiler under the 4000 single chip to read 51 wire optical encoder program