搜索资源列表
pic16877-timer
- pic单片机定时器0的相关程序,调试已经通过,通过定时器定时,完成秒表的功能,显示在led上-pic microcontroller Timer 0 associated procedures, debug, has been passed through the timers regularly, completion of the stopwatch functions, led on the show
stopwatch.rar
- 秒表可计时,用VHDL编译的源代码,从0.1到60秒计时,解压后直接用Quartus打开project即可,Stopwatch timer can be used to compile the VHDL source code, from 0.1 to 60 seconds from time, after extracting the direct use of Quartus can open the project
c51-timer
- c51 电子钟 功能完善 闹钟 秒表 整点报时等功能 -C51 electronic bell alarm clock stopwatch functions, such as the whole point timekeeping function
stopwatch
- VHDL语言设计的秒表,实现计时功能,实现报时功能,并且通过硬件实验。-VHDL language design stopwatch, timer function of the realization, the realization of time functions, and through hardware experiments.
timer
- C语言定时程序,主控芯片是ATmega8,采用中断方式实现实验板4位秒表计时-C language program from time to time, the master chip is ATmega8, using experimental board interruption means four stopwatch timing
timer
- 是一个秒表程序 按单位秒计时 用中断进行 还是比较精确的-Program is a stopwatch seconds per unit time or with interruptions for more precise
timer
- 51单片机做的电子钟程序,有按键闹钟显示跑表和闹钟功能,付有详细说明-51 single-chip electronic bell procedure done, there are buttons display stopwatch and alarm clock function is described in detail pay
shizhong
- 基于51单片机的编写的一个ds1302时钟芯片的一个c语言编程,实现计时,秒表,闹钟等一系列功能。-Write a ds1302 clock chip based on 51 SCM c language programming, timer, stopwatch, alarm clock, and a series of functions.
timer
- 自己编的利用c8051实现的t0计时器的马表-C8051 compiled to use their own implementation of the stopwatch timer t0
Electronic_stopwatch_features_plus_countdown
- 单片机做电子秒表。使用proteus仿真。设计要求:6位LED数码显示,计时单位为1/100秒。利用功能键进行启/停控制。其功能为:上电后计时器清0,当第一次(或奇数次)按下启/停键时开始计数。 当第二次(或偶数次)按下该键时停止计时,在一次按下启/停键时清0后重新开始计时。具有24秒减计数功能。 -SCM in the electronic stopwatch. Use proteus simulation. Design requirements: 6 LED digital dis
timer
- 运用at89s52实现计时秒表功能,有开始,暂停,清零,原理图有要的联系我-Use at89s52 achieve stopwatch function, a start, pause, clear, contact the schematic I have to
Timer
- 假定系统时钟为50MHz,试设计一个电子秒表电路,使其按0.01s 的步长进行计时。该电子秒表具有异步清零和启动/停止计数功能,最大能计到59.99s,并用数码管显示计数值。用发光二极管显示向分钟的进位信号。-Assume that the system clock to 50MHz, the design of an electronic stopwatch test circuit, so the step by 0.01s to time. The electronic stopwatch
Stopwatch
- 程序功能:秒表计时。有按键按下,则秒表开始计时,1暂停,0继续。-Program functions: stopwatch timing. A button press, then start the stopwatch timer, a pause, 0 to continue.
key
- 使用定时器学习秒表计时,中断0控制走表,中断1控制清零 -Learning to use timer stopwatch timing, interrupt 0 control away table, clear interrupt 1 control
Stopwatch
- 设计一个数字电子秒表,该秒表具有显示功能和清零、开始计时、停止计时等功能。 设计的要求如下: 1.以0.1秒为最小单位进行显示; 2.秒表可显示0.1~9.9秒的量程; 3.该秒表具有清零、开始计时、停止计时功能; -Sheji a digital electronic stopwatch, Gai stopwatch 具有 display and clear, start time, Tingzhi timer function. Design requirements a
stopwatch
- 单片机秒表制作 使用定时器0实现秒表功能 -Make use of microcontroller stopwatch stopwatch timer 0 to achieve
TIMER
- 精度为1/10秒的秒表,上电后数码管开始计时,带复位和暂停功能-Accuracy of 1/10 second stopwatch, starting on time after power LED, reset and pause with
Stopwatch
- 89c52定时器中断动态扫描数码管实现秒表-89c52 timer interrupts to achieve dynamic scan digital stopwatch
timer
- 基于89C2051的功能上包括了计时器和秒表两大功能 -89C2051-based functions including timers and stopwatch on the two functions
Hardware-timer
- 硬件定时秒表,使用PROTELUS对ATMEGA16为控制进行的仿真实验。-Hardware timer, stopwatch, PROTELUS ATMEGA16 for the control simulation.