搜索资源列表
fet140_spi0_07
- Descr iption: SPI Master communicates at fast as possible, full-duplex with // SPI Slave using 3-wire mode. The level on P1.4/5 is TX ed and RX ed to P1.0 // and P1.1. Master will pulse slave Reset on init to insure synch start. // Master norma
fet140_uart01_0115k
- // Descr iption: Echo a received character, RX ISR used. Normal mode is LPM0, // USART0 RX interrupt triggers TX Echo. // ACLK = MCLK = UCLK0 = LFXT1 = 8MHz // Baud rate divider with 8Mhz XTAL = 8000000/115200 = 0069 (0045h) // //* An externa
TX-RX-Project
- This an example for Short distance RF data communication.In this project some parameters Temperature,pressure recevived from sensors digitalized and converted to serial , finally transmitted through air . This data received in another unit and the op
01.RF-Interface-Rx-Tx-Auto_Normal
- This the program to communicate between to cc2500 Module in Normal Mode.-This is the program to communicate between to cc2500 Module in Normal Mode.
05.PC-Ctrld-robot_Wireless
- This is the program to communicate between PC and robot with cc2500 Module as TX Rx.
CC2430-tx
- CC2430点对点通信，完成通信功能，还有时钟电路报警功能-failed to translate
zigbee(cc2430)chuankou
- ZIGBEE串口收发程序(有改动)，发送内容位16进制代码，也可从PC机发送数据给CC2430然后返回。-ZIGBEE serial TX (modified), send the content-digit hexadecimal code, or from a PC to send data to the CC2430 and then return.
usbDevMuch
- LPC1700芯片USB批量传输源码。只要修改读写信号线以及PID、VID即可立即运行-Source code of USB Driver for LPC1700。You can run it imediatly only if you modify the RX/TX and PID/VID
cc2500_TI
- Working chipcon/TI cc2500 Lib. bitrate reg set to 10kbaud. recieve packet on GD0 int or GD2 goes high to indicate RX/TX overflow. flush and continue
LLC_PMBus
- LLC PFC power & support I2C PMBus function. LLC Tx all power datas to host (Voltage,current,power comsumption,tempture,fan speed etc..) Digital power is easier than analog just modify code.
TX-2440_BoardTest
- 主要基于S3C2440开发板的几个典型试验，包括串口、模数转换等。-Is mainly based on several typical test of the S3C2440 development board, including serial, analog to digital conversion.
point
- 点对点无线基本通信（仅实现发送接收 不含其它的成分）-point to point RX and TX
i2c_gpsl30
- 按照一般字符驱动处理的 I2C驱动程序，没有使用i2c体系结构。实现了 从模式读，和主模式写的功能。-IIC device driver that slave receive model and master TX model。
CC2530-UART2TEST
- descr iption：CC2520UART1-TX&RX-RECEIVE AND TRANSIT
ON-CHIP-PROGRAMS_PIC16F877
- the contents are pic16f877 programme for ADC, PWM and SERIAL TX and Rx-the contents are pic16f877 programme for ADC, PWM and SERIAL TX and Rx...
nRF24LE1
- nRF24LE1收发源码,最基本的键盘程序demo-nRF24LE1 Rx or Tx
Frequency-generator-and-protues
- 频率发生器+protues 单片机程序+protues仿真-Frequency generator and protues unsigned int code TX[10]={0,5000,2500,1667,1250,1000,833,714,625,556} // 不同频率之计量值 0, 100, 200, 300, 400, 500,600,700,800,900 Hz
tx
- 由51单片机简单的向串口发送数据的程序，程序短小，方便理解-51 MCU to send data to the serial program, short program, to facilitate understanding
DOUBLE-C51
- 第9章-单片机双机通信,用两片51来互相通信，通过RX和TX来进行收发信息。-Double 51MCU Communication.Use IO RX and TX to send and receive info.
CP9134_Tx_v1.0.51
- HDMI - 1.3 TX Control