搜索资源列表
keeloq TX V2.0
- 基于PIC的keeloq滚码算法及例程。-Based on PIC' s keeloq rolling code algorithm and routines.
u-boot-1.1.6-20090119.tar
- u-boot-1.1.6 for mini2440开发板。 支持网络下载,支持usb下载。基于友善之臂开发板。-u-boot-1.1.6 for mini2440
TX
- 1路视频光端机的发射端,VHDL源码,使用全FPGA芯片的硬件,内建成帧、时钟、SERDES-The launch of a video PDH client, VHDL source code, use the whole FPGA chip hardware, built-in framing, clock, SERDES
txmcu-proteus
- 天祥电子单片机开发板proteus仿真原理图DSN格式 包括51 AVR PIC 经典学习资料-Intertek electronic microcontroller development board proteus simulation schematic DSN format, including 51 AVR PIC classical learning materials
RF2411_avr(RF2401EK)
- 用NRF2401实现无线收发,与51单片机连接的时候,需要加电阻。-The nRF2401A can be programmed using a simple 3-wire interface where the data rate is decided by the speed of the micro controller. By allowing the digital part of the application to run at low speed while maximi
NRF905
- 带有DS18B20数字温度传感器的用作发射数据的nRF905无线数传模块,右边为用作接收数据的nRF905数传模块,其中的单片机可以通过串口和电脑相连,上传数据。-#include <at89x52.h> #include <intrins.h> #define uchar unsigned char #define uint unsigned int #define WC 0x00 // Write configuration regi
NRF24L01-TX
- MSP430F449通过控制按键发送nrf24l01C代码-MSP430F449 by controlling the key code sent nrf24l01C
cc2430-14
- CC2430的串口实验。将UART0 TX test赋给Txdata,串口发送数据UART0 TX test,在串口调试助手上显示。-CC2430 serial experiments. UART0 TX test will be assigned to Txdata, serial ports send data UART0 TX test, the serial debug assistant on the show.
4432_DKDBx_(TXRX_Switch_470M)(1)
- GT033-TRX 是一款低成本的ISM 频段FSK 收发模块, 可工作在240--930MHZ 中任意频点。功率可以最大配 置为20dBm(si4432),13dBm(si4431),接收灵敏度可达-118dBm,64 字节 TX/RX FIFOS,内置温度传感器, 8 位模数转换器,3 个I/O。支持跳频工作模式。可提供一个SPI 接口,通过MCU 设置就可调整各种参数(发 射功率.中心频点.带宽等)。无需外加功放电路就可实现远距离无线数据传输.-GT033-TRX is a l
tx
- 关于通信原理课程设计中HDB3编解码的一个VERILOG源代码-Principles of curriculum design on the communications HDB3 codec in a Verilog source code
51text
- 单片机初学者可用,开发板为TX-C,里面有AD,DA,I2C,通讯等,供参考-Single-chip can be used for beginners, development board for the TX-C, there are AD, DA, I2C, communications and so on, for reference
rx-tx
- 用STC89LE516AD控制nRF2401射频芯片进行数据收发和LED循环显示的C语言程序,里面有两个包,一个是发射程序包,一个是接收程序包. -NRF2401 with STC89LE516AD control data RF transceiver chip and LED display of the C language cycle program, which has two packages, one is the launch package, is to receive a
danpianji
- 片机能做什么,基本电子知识,如何用TX-1C单片机学习板学习单片机,C51知识简介,如何申请免费芯片样品。点亮一个发光管-Machine can do, and basic electronic knowledge, how to use TX-1C Single-chip Single-chip study panel study, C51 knowledge brief introduction, how to apply for a free sample chip. To light a
test_uart
- uart VHDL code : include tx,rx,parity bit control
thedesignofremotecontrolcar
- ,本设计采用2片AT89C52单片机构成主从式的控制系统。红外遥控部分采用遥控车模专用编、解码芯片TX-2/RX-2,提高控制的可靠性。采用红外传感器进行里程检测;超声波传感器进行障碍识别;感光电阻辅以步进电机控制的转动机构进行光源方向的检测,并能用软件控制小车行驶到光源附近。采用步进电机对小车的转向进行精确的控制。此外,采用四位LED数码管和若干LED发光二极管显示时间、行进的里程以及小车的各种状态;采用AT24C08串行EEPROM记录小车的行驶轨迹,并能按照所记录的轨迹自动行驶。 本次
tx
- 通信协议: 第1字节,MSB为1,为第1字节标志,第2字节,MSB为0,为非第一字节标志,其余类推……,最后一个字节为前几个字节后7位的异或校验和。 测试方法:可以将串口调试助手的发送框写上 95 10 20 25,并选上16进制发送,接收框选上16进制显示,如果每发送一次就接收到95 10 20 25,说明测试成功。 //这是一个单片机C51串口接收(中断)和发送例程,可以用来测试51单片机的中断接收 //和查询发送,另外我觉得发送没有必要用中断,因为程序的开
can_trans_sajat
- Header file to rx-tx CAN messages using MCP2515 CAN trx chip with atmel uC
TX-1BDS18B20
- DS18b20测温,通过串口,单片机传给电脑,让电脑显示出来-measure DS18B20
TX-1BDS18B20
- 驱动增强型单总线数字温度传感器DS1820进行温度检测-Single bus driver and enhanced DS1820 digital temperature sensor, the temperature detection
TX-1BDS18B201
- 驱动增强型单总线数字温度传感器DS1820进行温度检测-Enhanced single bus DS1820 digital temperature sensor